Manual Al-ko AL-KO 142 (page 30 of 124) (English, German, Dutch, French, Italian, Spanish)

594600

Zoom out

Zoom in

1/124

Preparing the equipment for use

ENGLISH 10

5.3 Cutter installation

Always switch off the engine, pull the spark plug cap

and wear protective gloves when fitting or replacing

the cutter!

A) Fitting the 3-tooth brush cutting blade

and the 4-tooth grass cutter (available as accessory)

• Place the brush cutting blade on the pressure

piece (25), ensuring that the cutting edges are

facing in an anti-clockwise rotational direction

(when looking at the tool in proper working

position).

• Fix the pressure washer (26).

• Place the nut protector (27) and turn safety nut (28)

onto the shaft.

Caution! Left hand thread - tighten counter

clockwise.

Take care that all parts are centered.

• Block the shaft with the stop pin (4) and tighten nut.

It is imperative that the safety nut (28) is

replaced, if it has become loose due to

frequent rem oval and tightening.

B) Fitting the chisel-tooth cutter (available as

accessory)

The procedure for installing the chisel tooth blade is

similar to the installation of the 3-tooth brush cutting

blade.

When using a chisel tooth blade, always

ensure that the metal guard (60 12 841) is

fitted in place of the guard and the retaining bracket.

• Unscrew the guard together with the retainer.

• Unscrew the four bolts and remove the retaining

bracket from the angular gearbox.

• Use the same four bolts to screw the metal guard

(60 12 841) onto the angular gearbox.

Transport protection for metal cutting blades

When the metal cutting blades are attached, the

transport protector must always be attached to cover

the blades when the device is being stored or

transported, or during work breaks during which the

engine is switched off.

• Position the transport protector with the

corresponding recess at one of the tips of the

metal cutting blade.

• Press the two tabs (a) on the transport protector

together to increase the internal diameter of the

transport protector.

• Lay the transport protector right over the cutting

tool. Position the inner shoulder (b) between the

metal cutting blade and the running disc.

• Open the two tabs again, and in doing so also

position the inner shoulder between the metal

cutting tool and the running disc at tab (c).

When restarting work, take the transport protector

back off by pressing the two tabs (a) together before

starting the engine.

Fig. 5

Fig. 6

Fig. 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko AL-KO 142 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko AL-KO 142 Manual

Product: