594609
19
Zoom out
Zoom in
Previous page
1/278
Next page
Assembly
469494_b 19
Do not start the motor if you are standing in
front of the discharge chute.
Start or operate the starter switch with caution
according to the manufacturer instructions.
Observe the local regulations governing the
minimum age of the operator.
Do not operate the device when under the in-
fluence of alcohol, drugs or medication.
Prior to each use, check the unit for damage
and have damaged or worn parts replaced.
Remove foreign objects in the working area.
Keep connecting cables out of the working
area.
Wear suitable work clothing:
Long trousers
Firm and slip-resistant footwear
Ensure that you have a sound footing when
working.
Keep other persons away from dangerous
areas.
Keep body, body parts and clothing away
from the cutter area.
Only work when there is adequate daylight or
artificial lighting.
Always disconnect the plug from the mains
and wait for the unit to come to a standstill:
Whenever you leave the lawn mower
Before you inspect the lawn mower,
clean it or perform work on it
After faults or unusual vibrations occur in
the unit
Before loosening blockages
Before eliminating stoppages
After contact with foreign bodies
ADVICE
After contact with foreign objects inspect
the mower for damage. Perform the ne-
cessary repairs before starting again and
begin working with the lawn mower.
If the lawn mower begins to vibrate strongly
in an unusual way, and immediate inspection
is necessary:
Inspect for any damage
Perform the necessary repair of dama-
ged parts
Tighten all nuts, bolts, and screws firmly
Play special attention when turning the lawn
mower or pulling it towards you.
Do not mow over obstacles (e.g. branches,
roots of trees).
Only remove cuttings when the motor is at a
standstill.
Never lift or carry the unit while the motor is
running.
Never leave the device unattended when it is
ready for operation.
ADVICE
If the mains supply conditions are not
sufficient, brief drops in the mains vol-
tage may occur when the unit is switched
on and this may affect other devices (e.g.
flickering lamps).
For a mains impedance of Zmax < 0.286
Ω these types of interference are not to
be expected.
ASSEMBLY
Observe the enclosed installation instructions.
CAUTION!
The unit must only be operated after it
has been fully assembled
OPERATION
Adjust the cutting height.
CAUTION!
Risk of injury!
Adjust the cutting height only when motor
is switched off and the cutting blade has
stopped!
ADVICE
Always adjust all wheels to the same cut-
ting height.
Cutting height adjustment depends on
the model.
Axle adjustment or central adjustment
ADVICE
Always adjust both axles to the same
cutting height.
1. To unlock, press the lever to the side and
hold. (1)
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko 4705 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko 4705 E in the language / languages: All languages as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info