560624

Aigger HSM5657A Manual

37
Zoom out
Zoom in
Previous page
1/78
Next page
37
1 Place the blind hemming foot, as is described on page 29.
2 Guide the material properly through the foot as is shown in the picture.
3 You can use the adjusting screw to set the right hem width. (illustration 53)
Free arm machine (illustration 54)
This machine disposes of a free arm. By removing the arm you can turn this machine into a
free-arm machine, which makes it easier to work on tubular pieces, such as trouser-legs and
sleeves.
Slide the part that you want to sew on to the arm and sew from the top. When you have
finished sewing with the free arm, you put the arm in its place again.
THE MAINTAINANCE
Cleaning the bobbin housing (illustration 55)
1 Set the on / off switch to "O" (OFF).
2 Remove the power cable from the sewing machine and take the plug out of the wall socket.
3 Bring the needle to the highest position.
4 Remove the bobbin housing (see page 31 bobbin replacement).
5 Turn the position finger outwards and remove the safety ring.
6 Remove the hook by taking it in the middle and pulling the whole outwards.
7 Remove any dust and thread from the safety ring, hook, drive and grab track with a brush.
8 With a cloth that you have moistened with sewing machine oil, dust and other rests can be
removed from the grab track.
9 Clean the bobbin housing.
10 Mount the hook again with the notch at the top and push the position fingers back into the
right position to keep the safety ring in its place.
WARNING When exchanging the light bulb, remove the plug from the wall socket. To prevent
burns, you must be extremely careful when exchanging the light bulb. Light bulbs are available
from the sewing machine specialist shop. Use a 15W light bulb. If you use a light bulb with a
higher wattage the guarantee expires.
Cleaning the transporter
1 Set the on / off switch to "O" (OFF).
2 Remove the power cable from the sewing machine and take the plug out of the wall socket.
3 Remove the screw on the left-hand side of the needle plate with the screw driver. Remove
the needle plate.
4 Clean the transporter with a brush.
5 Place the needle plate back in its place.(illustration 56 and 57)
Oiling the machine (illustration 58)
The arrows in the picture show which points in the machine must be oiled. Before you apply
the oil, these spots must be cleaned. Apply one or two drops of sewing machine oil of a good
quality. Should the machine not function properly after it has not been used for a long time,
you must apply a few drops of oil at the marked spots. Then you allow the machine to run fast
for a few minutes with all the lids closed. Sewing machine oil is available at the sewing
machine specialist shop.
WARNING! Do not forget after oiling the machine to sew on a piece of waste material first, to
catch any superfluous sewing machine oil.
English
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aigger HSM5657A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aigger HSM5657A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info