560624

Aigger HSM5657A Manual

38
Zoom out
Zoom in
Previous page
1/78
Next page
38
English
SOLVING PROBLEMS
If the power cable of the device is damaged, immediately take the plug from the wall socket. The power
cable must only be replaced by indicated representatives of the supplier.
Problem Possible cause Solution Pag.
The needle thread There is something wrong with the needle. Exchange the needle. 29
breaks. The thread is too thin for the material. Select a thread that issuitable for the 27
sort of material that you are sewing.
The thread is not properly placed in Put the thread in properly. 31
the needle.
The bobbin thread The bobbin thread has not been threaded Thread the bobbin thread properly. 31
breaks. properly.
Dust has assembled in the bobbin housing. Clean the bobbin housing. 39
Stitches are being The upper thread is not properly threaded. Thread the upper thread properly. 31
skipped.
The combination of material, thread Select a thread and needle that are suit- 27
and needle is not correct. able for the sort of material that you sew.
The needle is bent or blunt. Replace the needle. 29
The needle is not properly installed. Install the needle properly. 29
Dust has assembled under the needle Remove the needle plate and 39
plate or in the bobbin housing. clean the bobbin housing.
The material is The upper thread is not properly threaded, Thread the upper thread in properly 31
wrinkled. or the bobbin is not properly installed. and install the bobbin thread properly.
The combination of material, Select a thread and needle that are 27
thread and needle is not correct. suitable for the sort of material
that you want to sew.
The needle is bent or blunt. Replace the needle. 29
When you sew thin materials, Shorten the stitch length or place a 29
the stitch is too large. supporting cloth under the material.
The thread tension is not correct. Adjust the tension of the upper thread 29
The needle breaks. You are pulling the material too hard. Guide the material loosely.
The pressure foot that you use, Attach the right pressure foot for the 29
is not suitable for the sort of sort of stitch that you want to sew.
stitch that you want to sew.
The needle has not been installed properly. Install the needle properly. 29
The stitch is not The pressure foot that you use, Attach the right pressure foot for the 29
sewn properly. is not suitable for the sort of sort of stitch that you want to sew.
stitch that you want to sew.
The thread tension is not correct. Adjust the tension of the upper thread. 29
The thread is entangled, for Remove the entangled thread. 39
example in the bobbin housing. If the thread in the bobbin housing is
entangled, then clean the bobbin housing.
The device makes a Dust has assembled under the need- Clean the bobbin housing. 39
lot of noise. le plate or in the bobbin housing.
The machine does The sewing machine is not switched on. Switch the machine on. 27
not work.
The On / off switch is not set to on. Switch the on / off switch to "on". 27
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aigger HSM5657A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aigger HSM5657A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info