Manual Aigger HSM5657A (page 33 of 78) (English, German, Dutch, French)

560624

Zoom out

Zoom in

1/78

1. Secure the zigzag foot.

2. Select the right stitch, set the stitch length to 4mm and lower the thread tension.

3. Sew parallel stitches with 1 cm intervals. TAKE NOTE: you do not need to sew

reverse/strengthening stitches or cut off the thread.

4. Pull the lower thread to create pleats. Iron the pleats with an iron.

Embroidering (illustration 48 & 49)

1. Place the embroidery plate on the needle plate.

2. Set the choice of pattern button to the required zigzag stitch.

3. Tighten the material as much as possible between the embroidery rings (not supplied, can

be obtained at speciality shops) with the inside of the material to the underside of the

inner ring.

4. Place the work underneath the needle and lower the foot lever without using the foot pedal.

5. Turn the fly-wheel and pull the lower thread up through your work at the starting point.

Make a few attachment stitches.

6 Pick the ring up between the thumb and index finger of both hands and apply pressure to

the material with your middle and ring fingers. You can then use your little finger for

support on the outside of the ring.

COMMENTS:

a. Stitch around the outline of your design by moving the embroidery ring.

b. You can now fill your design by first sewing from the outside to the inside and then from

the inside back to the outer edge, until the entire design is completed. Ensure the stitches

run alongside each other.

c. You can create a long stitch by moving the embroidery ring quickly. A short stitch is

achieved by moving the ring slowly.

d. Sew a few straight stitches at the end to finish off.

Making buttonholes (illustration 38)

PREPARATION

1 Determine the length of the buttonhole

2 Draw the centre line with a piece of chalk.

REMARK

Try this first on a piece of the same material, before you actually set to work. (illustration 39)

Setting to work

1 Place the material and see to it that the middle of the pressure foot runs even with the line

that was drawn on the piece of material. Then move the plate of the pressure foot and let

the opening of the pressure foot run even with the drawn hole.

2 Set the button for the choice of pattern to A. Stop sewing when you reach the marked chalk

Pressure foot Choice of pattern Stitch length

Buttonhole foot ( ) ( ) 0.3~1

()

Pressure foot Choice of pattern Stitch length

None Zigzag stitch All

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aigger HSM5657A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aigger HSM5657A Manual

Product: