560624

Aigger HSM5657A Manual

29
Zoom out
Zoom in
Previous page
1/78
Next page
29
Button for sewing backwards (illustration 15)
Push the button down to sew backwards. The material is then automatically transported
backwards. You can use this function to strengthen the sewing.
Stitch selection button (illustration 16)
Ensure the needle is in the highest position. This is done by turning the fly-wheel. Turn the
selection button to the required stitch.
Once you have set the stitch length between 0 and 4, you can choose between 10 different
stitches, which will have the same colours as the 0-4 numbers of the stitch length.
Once you have set the stitch length button to SS, you can sew stretched stitches by way of
selecting the stitches with the same colour as the SS symbol (A-J).
Exchanging the bobbin
1 Bring the needle to the highest position
2 Bring the pressure foot up by lifting the pressure foot lever upwards. (illustration 17)
3 Then open the protecting cover of the bobbin housing. (illustration 18)
4 Open the lock of the bobbin housing and then take the bobbin housing out of the machine
together with the bobbin. (illustration 19)
5 Hold the bobbin housing with one hand and remove the bobbin with your other hand.
(illustration 20)
6 Insert a new bobbin. (illustration 21)
7 Put the thread in as indicated in the picture. (illustration 22)
8 You can now place back the bobbin housing by keeping the lock open and pushing it
inwards over its pin. (illustration 23)
9 See that approximately 15cm of thread sticks out of the bobbin. (illustration 24)
Winding bobbins
1 Turn the motor interlocking loose by turning the button towards yourself.
(illustration 25 and 26)
2 Thread the yarn in as is indicated in the picture. (illustration 27)
3 Pull the end of the thread through the hole in the bobbin as indicated in the picture.
(illustration 28)
4 Place the bobbin on the bobbin winder and move this to the right until it clicks. When the
bobbin has been wound a little bit, you remove the thread end. (illustration 29)
5 You can now continue winding, until the bobbin winder stops automatically.
(illustration 30)
6 Turn the motor interlocking to the right position. (illustration 31)
Threading the thread (illustration 32)
1 Place the top thread spool on to the holder that is there for this purpose. Turn the needle
to the highest position so that guide 4 becomes visible. Lift the pressure foot holder up by
moving the pressure foot holder upwards.
2 Then thread the yarn along the guides 1 and 2.
3 Lead it via the tension control 3 to guide 4, to thread guide number 5.
4 Then lead the thread via thread guide number 6 to the needle and put the thread through
the needle from front to back.
Bringing the bobbin thread up (illustration 33)
1 When you have threaded the upper thread through the needle you can bring the bobbin
thread up by turning the flywheel towards yourself. Turn so far until the needle has made an
upward movement in once and the needle is again in its highest position.
Nederlands
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aigger HSM5657A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aigger HSM5657A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info