560624

Aigger HSM5657A Manual

27
Zoom out
Zoom in
Previous page
1/78
Next page
27
Exchanging the needle
1 Pull the plug from the wall socket.
2 Turn the flywheel until the needle is in its highest position.
3 Turn the needle clamp loose as shown in the picture. (illustration 6)
4 Take the needle from the needle holder.
5 Insert a new needle.
6 Then screw the needle clamp as tight as possible.
Check the needles at regular intervals. The needle must be straight and sharp as is shown in
pictures a and b. Do not use any needles that are bent or blunt, as in pictures c, d, e or f.
(illustration 7)
Removing and placing the pressure foot (illustration 8, 9 & 10)
1 Turn the wheel until the needle is at its highest position. Lift the pressure foot up by
moving the pressure foot lever upwards.
2 By pressing the foot interlocking the sewing foot automatically falls from its holder.
3 Insert the foot under the holder in such a way that the pen of the foot is under the notch in
the holder. By then taking the pressure foot lever down and pressing the foot interlocking,
the foot automatically clicks into its holder.
Controlling the thread tension (illustration 11)
1 The upper thread and the bobbin thread must interlace with each other in the middle of
the two layers of material.
2 If the top thread tension is too low (this is visible when the interlacing is at the bottom of
the two layers of material), you can raise this by turning down the top tension control
button (1 > 9).
3 When the top thread tension is too high (this is visible if the interlacing is at the top of the
two layers of material), you lower this by turning the top tension control button upwards
(9 > 1).
Controlling the bobbin thread tension (illustration 12)
If you do not succeed in controlling the top thread tension to get the interlacing in the right
position, you can try this by adjusting the bottom thread tension. To increase the tension, you
turn the tension screw in the direction as indicated in the picture.
To lower the tension you turn the tension screw in the opposite direction.
To check the tension you take the thread as indicated in the picture, now the bobbin housing
must drop down 3 to 4cm. (illustration 13)
To get a fine zigzag stitch the top tension must be set a little slacker than with a straight lock
stitch. The needle thread must be slightly visible at the bottom of the material.
Stitch length control (illustration 14)
1 The numbers on the stitch length selection button approximately correspond with the
stitch length in mm.
2 You can select the desired stitch length with this button. In the picture this is set to a stitch
length of 2 mm.
3 When sewing extensible seams you set the stitch length to SS (stretch stitch).
English
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aigger HSM5657A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aigger HSM5657A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info