782361
78
Zoom out
Zoom in
Previous page
1/136
Next page
72
SCOOPY+ S - User Manual
AoIP settings
These settings apply to any connection using the IP protocol, hence all Ethernet or mobile IP interfaces
are concerned. They can be found in the sub-menu Setup / Network / AoIP Parameters, and details
about these settings are described in 4.4.1, "AoIP Parameters" section.
The most common and convenient connection method is by using the SIP protocol: select "SIP" as first
parameter (Default protocol).
If a SIP server is used, you should register the SCOOPY+ S on this server. Use the sub-menu to enter the
SIP account data and activate the SIP registration. Check that the codec is properly registered thanks to
the indicator on the base screen ("S" sign at the middle of the top line), otherwise via the sub-menu
Tools / About, SIP Status information.
Besides, for links over the Internet, most often the link passes through a NAT router which "hides" to the
codec the characteristics of the public access: public IP address and RTP ports actually used. This can
make the SIP transactions fail, or get a non-optimal route through the network. To avoid this, a STUN
server is often used; the corresponding settings are also found in the AoIP Parameters sub-menu.
Check that the public address discovery has succeeded: Tools / About sub-menu: Public IP information
(its mere presence shows the discovery has succeeded). The type of NAT detected by the Scoopy+ S is also
shown in this sub-menu (NAT Type).
If you wish to use the "Direct RTP" mode instead of SIP for outgoing calls, select "RTP Direct" for the first
parameter (Default protocol). This mode involves in fact no signalling protocol such as SIP, but its
operation is somewhat similar: a codec "calls" another, in fact initiates a link by directly sending a
stream to the other end. The "receiver" of the call should be configured for accepting this incoming
"call" and sending its own stream back to the initiator of the link.
Ethernet interface
Use an RJ45 cable to connect the SCOOPY+ S to a router or switch. A couple of LEDs on the Ethernet
socket (back panel, see 3.2.2) indicate the status and activity of the Ethernet link.
It may be necessary to configure the network interface depending on the local installation, especially
when it does not include a DHCP server. The Ethernet interface settings are reachable via the sub-menu
Setup / Network / Ethernet Parameters.
The various parameters are described in 4.4.1, "Ethernet Parameters" section.
In most cases, you can use the following settings:
Mode: "DHCP"
Link Mode: "Auto-Negotiation"
Network Quality: "Middle"
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeta Scoopy plus S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeta Scoopy plus S in the language / languages: English as an attachment in your email.

The manual is 5.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info