782361
62
Zoom out
Zoom in
Previous page
1/136
Next page
56
SCOOPY+ S - User Manual
RTP Port (SIP): the default port for RTP/SIP audio streams is 5004 (UDP), but you can enter a
custom value here if desired.
RTP Port (Direct): port allocated to the transmission in Direct RTP mode; should not be the
same as the RTP port for SIP.
RTP DSCP: if the transmission network supports DiffServ to manage the media priority, you
can set here the type of service which is assigned to the stream transmitted by the codec.
You should enter here a decimal value, e.g. 46 for the maximal priority code "Expedite
Forwarding". The default value is 0, "Best Effort".
Packet Replication: (see also 2.1.1 and page 10 regarding this feature) you can select here
the setting for packet replication:
0 => standard mode without replication (default setting)
1 => packet replication without interleaving
2 => packet replication with interleaving: the second packet is delayed; robustness is improved
but latency is increased.
Direct RTP Accept: when this box is checked, the codec accepts incoming RTP streams. If it is
not checked, incoming streams on the Direct RTP port are ignored.
Direct RTP Send only: if this is activated and the operator sets an outgoing call, the unit does
not expect to receive an RTP stream and rather decodes its own stream. The device keeps
sending data until the user releases the link on purpose. In this use case the "RTP Timeout"
parameter (see further) is irrelevant.
This parameter should not be checked at the same time as "Direct RTP Accept".
Direct RTP Timeout (default 30 seconds): after a link is established, if no data is received
within this time period, the device "releases" the link (i.e. stops sending its own RTP stream)
and comes back to the idle state (Direct RTP Accept is unchanged).
Multicast Mode: if the selected mode is Multicast, the transmission is unidirectional. Select
with this menu if the codec must be sender of a multicast stream, or rather receiver of such
stream.
Multicast Control Port: this port number (UDP) is used for sending control packets
accompanying the multicast stream. Default value is 6000.
Multicast Audio Port: this port number (UDP) is used for transporting the multicast audio
stream. Default value is 6001.
Note: this setting is not related to the RTP Port settings valid for RTP/SIP or Direct RTP.
Multicast TTL: TTL value applicable to the RTP multicast audio stream. Default: 254.
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeta Scoopy plus S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeta Scoopy plus S in the language / languages: English as an attachment in your email.

The manual is 5.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info