587610
72
Zoom out
Zoom in
Previous page
1/184
Next page
72
EN
IMDCFJ. 12.05 6343841_03
Code
Alarm
Code
Pre-alarm
Causes Notes
37 137 DC Bus over-voltage (code APY 6)
40 140
PFC Converter Fault
Error in the PFC module
Software error (code APY 9)
41 141 Over current in acceleration mode Software error (code APY 10)
42 142 Overload (code APY 11)
43 143 Over-current at constant speed Software error (code APY 12)
44 144 Over current in deceleration mode Software error (code APY 13)
45 145
Compressor not connected
correctly
(code APY 14)
46 146 No communication (code APY 15)
47 147
Cooling fin temperature sensor
error
(code APY 16)
51 151 Anomalous condition
Protection frequency against over-current and overheating
reduced. (code APY 20)
54 -- Cycle reverse valve faulty
The cycle reverse valve could be faulty or broken. (see
8.4)
55 155 Water inlet high temperature
The water inlet temperature has exceeded the set_install-
er (H) parameter value. Probable boiler presence on
same plant. At the third intervention of the pre-alarm, the
machine goes into alarm mode and blocks
-- 156
Cycle reverse due to high
temperature of the pressing line
gas
This pre-alarm indicates the intervention of defrosting
due to cycle reverse without having respected the times
between cycle reverses. Cycle reverse has been triggered
by the pressing line gas high temperature partialisation
threshold being exceeded, set_factory (6)-set_factory (4)
= default 130°. This pre-alarm does not cause compressor
stop and does not have a limited number of interventions
57 157
Reading error of the DHW control
board remote probe.
This pre-alarm indicates a remote probe fault or a commu-
nication problem with the DHW control board. The alarm is
only active if the parameter (0)=2 or the parameter (8)=4 in
the menu with password = 30
58 158
Outdoor air temperature probe
reading error
This pre-alarm indicates an outdoor air temperature probe
fault when the DCP is present or the machine is in heat
pump mode.
59 159
Inlet water probe
no condenser
(ONLY WRL)
This pre-alarm indicates a condenser inlet water tempera-
ture probe fault
60 160
Output water probe
no condenser
(ONLY WRL)
This pre-alarm indicates a condenser outlet water tem-
perature probe fault
61 161 Over-current Carel Inverter
62 162 Compressor motor overload Carel Inverter
63 163 Over-voltage Carel Inverter
64 164 Under-voltage Carel Inverter
65 165 Drive overheating Carel Inverter
66 166 Drive underheating Carel Inverter
67 167 Hardware over-current Carel Inverter
68 168 Compressor overheating Carel Inverter
69 169 Reserved Carel Inverter
70 170 CPU error Carel Inverter
71 171 Default parameters Carel Inverter
72 172 DC bus ripple Carel Inverter
73 173
No communication between invert-
er and uPC
Carel Inverter
74 174 Drive temperature sensor fault Carel Inverter
75 175 Self-configuration failed Carel Inverter
76 176 Inverter drive disabled Carel Inverter
77 177 Motor phases error Carel Inverter
78 178
Cooling fan
Inverter faulty
Carel Inverter
79 179 Speed fault Carel Inverter
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aermec MODUCONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aermec MODUCONTROL in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info