587610
73
Zoom out
Zoom in
Previous page
1/184
Next page
73
EN
IMDCFJ. 12.05 6343841_03
ATTENZIONE:
Si ricorda che i preallarmi sono a riarmo automatico, mentre gli allarmi sono a riarmo manuale.
Dalla versione software 3.9.0 è stato introdotto il reset degli allarmi tramite contatto remoto di ON/OFF se abilitato.
Da posizione on, se passa in off e ritorna in on entro 5 secondi resetta gli allarmi; tramite il contatto ON/OFF è possibile eseguire
al massimo 3 reset ogni ora.
Prima bisogna resettare gli allarmi con tasto “R”.
In caso di mancanza di tensione vengono resettati gli allarmi.
Code
Alarm
Code
Pre-alarm
Causes Notes
80 180 PFC fault
Alarm that occurs with PFC enabled while the bus DC is
very low
81 181 PFC overload trip
This alarm will no longer be present in the new firmware
versions.
82 182 Input voltage error
When the power supply drops below 170 V with engine running
83 183 Generic inverter error Carel Inverter, carel modbus address 213
84 184 Probe B1 fault (uPC) Control wiring
85 185 Probe B2 fault (uPC) Control wiring
86 186 Probe B3 fault (uPC) Control wiring
87 187 Probe B4 fault (uPC) Control wiring
88 188 Probe B5 fault (uPC) Control wiring
89 189 Probe B6 fault (uPC) Control wiring
90 190 Probe B7 fault (uPC) Control wiring
91 191 High pressure alarm (uPC) Control wiring
92 192 Low pressure alarm (uPC) Control wiring
93 193
Gas high temperature alarm
pressing line (uPC)
Control wiring
94 194
Pressure differential lower than that
specified (uPC)
Control wiring
95 195
Compressor start-up failed (uPC)
Control wiring
96 196
Time exceeding operational limits
alarm (uPC)
Control wiring
97 197 Super Heat low alarm (uPC) Control wiring
98 198 MOP alarm (uPC) Control wiring
99 199
Low intake temperature alarm
(uPC)
Control wiring
200 300
EVD EVO alarm: Evotunes alarm (uPC)
Control wiring
201 301
EVD EVO regulation alarm (uPC)
Control wiring
202 302
EVD EVO system alarms probe
errors alarm (uPC)
Control wiring
203 303 Reserved. (uPC) Control wiring
204 304
No communication between invert-
er and uPC. (uPC error)
Control wiring
205 305
Inverter not compatible with the
compressor selected (uPC)
Control wiring
206 306
Delta P greater than the permit at
start up (uPC)
Control wiring
207 307 Low pressure limit Discharged unit
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aermec MODUCONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aermec MODUCONTROL in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info