382748

AEG step 570 x Manual

6
Zoom out
Zoom in
Previous page
1/64
Next page
5
ENGLISH
STEP 570 X, STEP 600 X
To avoid vibration, clamp metal sheets onto a wooden base.
To saw metal, use cooling agents along the cutting line (oil, white spirit).
Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light
building materials for walls). Harder materials (metals) must first be drilled with a hole
corresponding to the size of the saw blade.
Move the base plate to the rearmost setting in order to obtain the best possible
cutting angle for starting the cut.(see section ”Adjusting the base plate”)
1. Set the pendulum stroke at the pendulum stroke control to “0”.
2. Without switching the machine on, place it with the front edge of the base plate on
the cutting point.
3. Switch the machine on and carefully lower the saw blade already running into the
material.
GERMANY
274315
III
I
I
I
0
GERMANY
274315
III
II
I
0
G
ER
MA
NY
27431
5
III
II
I
0
Using the parallel guide or circle cutting, parallel cuts of 0–200 mm, circular cuts of
100–400 mm are possible. Use cross-cut saw blades.
*Not included in standard equipment, available as an accessory.
Push the parallel guide, with the contact
surface facing downwards, through the
lugs in the base plate and fasten it in
position with the capstand–headed screw.
For cutting from the left or from the right,
push the parallel guide in from the
appropriate side.
Push the parallel guide, with the contact
surface facing upwards, through the lugs
in the base plate and fasten it in position
with the capstand–headed screw.
Tighten the centre point into the parallel
guide from the top.
Ensure that the saw blade and the circle
centre point form one single line.
Further accessories with part numbers are shown in our catalogues.
In order to guarantee constant readiness for operation, the machine should be
checked for worn carbon brushes at one of the AEG after–sales service agencies.
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the ten–digit
No. as well as the machine type printed on the label and order the drawing at your
local service agents or directly at: Atlas Copco Electric Tools GmbH, Postfach 320,
D–71361 Winnenden.
Sawing sheet
metal
Plunge cuts
Parallel guide
and circle cutting
guide
(Accessory*)
Assembly of
parallel guide
Cutting a circle
Maintenance
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG step 570 x at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG step 570 x in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info