382748
5
Zoom out
Zoom in
Previous page
1/64
Next page
4
ENGLISH
STEP 570 X, STEP 600 X
The stroke rate appropriate to the material being worked on can be taken from the
following table, and the corresponding letter shown on the setting wheel.
Material Stroke rate
Wood G
Steel D-E
Aluminium D-E
Rubber A-C
Intermittent use
Switching on: Press On-/off switch
Switching off: Release On-/off switch
Continuous use
Switching on: Press the On-/off switch and
then the locking button, after that release
on-off switch.
Switching off: Press the On-/off switch and
then release.
By adjusting the pendulum action the cutting depth of the saw blade teeth is
increased or decreased. As a rule of thumb:
Soft material Large pendulum stroke
Hard material Small or no pendulum stroke
Clean cut surface No pendulum stroke
The appropriate degree of pendulum effect can be taken from the following chart
and compared with the marking at the pendulum stroke lever.
Material Degree of swing action
Wood I - III
Plastic I
Aluminium 0 - I
Steel 0
Ceramics 0
Rubber 0
The stroke rate shown in the chart is only
a suggestion for your general guidance!
The stroke rate can be set on the stroke rate control even while the motor is
running.
1. Set the stroke and pendulum stroke according to the material to be cut.
2. Position the machine with the front part of the base plate on the material, and
switch on.
3. Press the machine downwards onto the material and guide it along the cutting line.
Do not press down too hard on the piece you are cutting. Light pressure on the saw
blade is sufficient to achieve the optimum rate of sawing.
When cutting along a score line, use the marking on the anti-splintering device as an
optical guide.
To obtain a perfectly straight cut, clamp a strip of wood as a guide along the material
or use the parallel guide (accessory).
For cutting at an angle, or cutting a bevel, adjust the base plate.
For sawing close to the edge, set the base plate at its rearmost position.
On-/off switch
Adjusting the
pendulum stroke
Advice for
operation
Hints
B
A
B
A
1
2
15
0
III
II
I
0
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG step 570 x at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG step 570 x in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info