473798
60
Zoom out
Zoom in
Previous page
1/132
Next page
Protect PV.500 Operating Instructions
56 of 70 80000031354 BAL
7.2.5 Network Integration Configuration
For network integration, you will need free IP address for the COM
server, the subnet mask plus the IP address for the gateway. This
information can be obtained from your administrator if necessary.
Start the "Digi Device Discovery" tool.
The tool searches the network for Digi modules. The modules
found are displayed. If several units are found, please select
the unit to be configured using the MAC address. This can be
found on the Digi module sticker on the COM server. If no
modules are detected, check your network and and firewall
settings. Run the search again using "Refresh view".
Select the required unit. You can enter the necessary network
parameters using the right mouse button + "Configure network
settings".
Use "Save" and "Reboot" to apply the settings and complete
the installation.
Exit the "Digi Device Discovery" tool.
You can use the "ping" command to test whether the COM
server can be reached on the network.
7.2.6 Configuration of the Virtual COM Port
Communication with the COM server takes place via a virtual COM
port, which is implemented by means of a RealPort driver. In order
to do this, the RealPort driver needs to be installed and configured.
Start the RealPort driver installation process. For this purpose,
the COM server must be connected to the network and the
network parameters must be set.
The installation program searches the network for Digi
modules. The modules found are displayed along with the
configured IP address and MAC address. If several units are
found, please select the unit to be configured using the MAC
address and select "Next". The MAC address can be found on
the Digi module sticker on the COM server. If no modules are
detected, check your network and and firewall settings. Run
the search again using "Refresh view".
In the "Describe the Device" window, you can make RealPort
settings. This is where you need to select the COM port via
which the application is to communicate later. All other settings
can be left as per the factory settings.
Select "Finish" to complete the installation.
The application can communicate via the set COMx port with a
baud rate of 115.2 kB as standard. 9600 kB is also possible as an
alternative. Between these two transmission rates, the COM server
has an autobaud detection function.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Protect PV 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Protect PV 500 in the language / languages: English as an attachment in your email.

The manual is 1,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Protect PV 500

AEG Protect PV 500 User Manual - German - 136 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info