473797
36
Zoom out
Zoom in
Previous page
1/51
Next page
Protect PV.250 Operating Instructions
Page 36 of 51 80000027023 BAL, en
6.2.5 LEDs
Power LED
This signals that the supply voltage is connected. If this LED does
not light up, please check that the supply voltage is connected cor-
rectly.
Status LED
This flickers when there is any network activity on the serial port.
Periodic flashing indicates that the port has a valid connection to
another network station.
Error LED
This uses different flashing codes to indicate error statuses on the
COM server or the serial port.
1 x flashing = Check network connection
The COM server cannot receive a link pulse from a switch or a
hub. Please check the cable or the network components.
2 x flashing = Check serial data format
At least one mark with a parity/frame error was received on the se-
rial port. Please check that the set serial parameters and the serial
data cable are correct.
All LEDs on = Self-test fault
The self-test performed after each start or reset of the COM server
could not be terminated correctly. This fault can occur if you have
cancelled an update of the COM server prematurely.
Please refer to the supplied manual on the CD-ROM from W&T for
more information about the COM server.
6.2.6 Installation of the Virtual COM Port
In order to communicate via the COM server, it must be integrated
into the network and a virtual COM port must be set up on a com-
puter.
6.2.7 Network Integration Configuration
For network integration you will need a free IP address for the
COM server, the subnet mask and the IP address for the gate-
way. This information can be obtained from your administrator if
necessary.
Now please remove the product CD from the W&T quick-start
instructions supplied and start this CD-ROM on a computer in
the same subnet as the COM server, then please install the
"WuTility" tool.
Use the "Scan" button to search the local network for W&T de-
vices. If several devices are found, please select the device to
be configured on the basis of its Ethernet address. This can be
found on the sticker on the COM server, and starts with
EN=00c03dxxxxxxxxx.
Select the required device and press the "Assign IP address"
button. Please enter the necessary parameters here.
Save and exit; the COM server is now installed in the network.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Protect PV 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Protect PV 250 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Protect PV 250

AEG Protect PV 250 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info