480501
83
Zoom out
Zoom in
Previous page
1/114
Next page
83
ENGLISH
3. The connection of “Continuous +” (continuous cur-
rent connection) may dier depending on the vehicle
type. (However, this is required for storing of the radio
stations.)
In order to assure all functions, installation according
to these instructions is necessary. In case of doubt,
please contact an authorized car workshop.
Because of the dierent vehicle types and vehicle
manufacturers, correct wiring of the ISO connector
is no assured even when the ISO plug connectors t
mechanically. Thus it may be necessary to change the
electric connection or to use a vehicle-specic adap-
tor.
NOTE
In case of correct connection, the radio can be
switched on and o with the ignition. In case of
possible loss of stored radio stations, the radio is
not provided with the “Continuous +” required
for station storage.
CAUTION
In case of connection to “Continuous +” without
ignition, an unnecessary load may be caused for
the car battery even when the radio is switched
o. In the worst case, this may lead to discharge
of the car battery.
4. Depending on the vehicle type, interferences may
occur during operation of the radio. These can be
eliminated with an additional noise lter. Your set is
already equipped with a noise lter as standard. In
spite of this, interferences may be caused depending
on the vehicle.
Noise lters are available from car accessory sellers
and/or your car workshop.
5. When installing your radio, take care that there is
sucient free space at the rear of the radio to assure
sucient cooling.
6. There are two dierent standards for the antenna
connection. The rst one is the old one (50 Ohm) with
a long projecting round contact on the vehicle side
and a round socket on the radio side. The second one
is the ISO standard antenna plug (150 Ohm). Adapters
for both formats are oered by car accessory sellers
and/or your car workshop.
NOTE
To be strictly observed for VW/Audi: The antenna
of your vehicle may be an active antenna. This
requires a voltage supply only provided by the
original car radios. If this should be the case,
please use an antenna adapter for phantom feed.
Antenna adapters are available from car acces-
sory sellers and/or your car workshop.
Mounting Instruction
The correct tools are self-explanatory for a car hi
installation.
Insert the unit into the ISO slot or select a location
where you can reach all controls and the unit is not in
the diver’s way.
Connect only to a properly installed 12 V battery.
Connect only via the ISO connectors.
Install the unit in such way that no overheating is pos-
sible and the unit is well ventilated.
If the installation angle exceeds 30° the unit might not
perform well.
Avoid installing the unit where it is subjected to high
temperature, such as from direct sunlight, hot air from
the heating ducts, or where subjected to dust, dirt or
excessive vibration.
Contact your car manufacturer or the local dealer if
vehicle modications are necessary.
Installation in ISO Slot
A
B
C
D
C
Remove sleeve (D) and frame (B) from the unit. Use
installation keys (C), if necessary.
Place the sleeve in the ISO slot.
Bend the claws outward with a screwdriver for perfect
t.
Check the sleeve for tight t.
Connect the ISO female connectors of the unit with
the two ISO male connectors of the vehicle.
Connect the antenna to the antenna connector at the
rear of the unit.
Secure the unit against theft, if necessary. Attach bolt
and mounting strip with the fastening materials at the
rewall.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG AR 4021 BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG AR 4021 BT in the language / languages: English, German, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 7,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info