660217
7
Zoom out
Zoom in
Previous page
1/15
Next page
7
Programming
What is stage
cooking?
Stage cooking enables
several different cooking cycles, or
stages, to be used consecutively
without repeated input from the user.
Stage cooking can be set to defrost
food initially, then cook it, and then
keep the food warm until serving time.
Programming
Preheat Setting
The convection temperature setting
can be set between 150°F to 475°F
(65°C to 250°C). It is recommended
to set the preheat setting to the most
commonly used temperature for that
oven. The factory default preheat
setting is 475°F (250°C).
To program the preheat setting:
1. Turn oven on to set preheat.
2. Press Program Save pad.
3. Press Temp Entry pad.
4. Enter desired temperature by
using the numeric key pads.
• Temperature must be entered
in 5°F (5°C) increments. If
not, the temperature will
automatically change to the
nearest 5°F (5°C).
5. Preheat temperature is changed.
Programming Multiple Stages
Stage cooking allows consecutive cooking cycles without interruption.
Up to four different cooking cycles can be programmed into a memory pad.
To use stage cooking:
1. Follow steps 1 through 6 above.
7. Press Stage pad.
• This will begin programming for the next cooking
stage.
• Display indicates stage to be programmed.
• Enter cook time, temp and power level as in steps 4. 5 and 6.
• To enter another cooking stage for that pad, press Stage pad
again.
• Up to four different stages can be programmed.
8. Press Program Save pad to save the program and
changes.
9. To discard changes, press Stop/Reset pad before
pressing Program Save pad.
Programming Pads
Oven is shipped from the factory for single digit programming. To change
the oven default to double digit programming, see User Option section. To
program the amount of time, power level, or temperature setting for a pad:
1. Oven must be ON.
• Press Preheat On/Off pad.
Oven Preheating 475°F or 250°C shows in display
with Oven Preheating ashing.
2. Oven reaches preheat temperature.
Ready 475°F or 250°C shows in display with Ready ashing.
Press Program Save pad.
• Programming mode begins.
Enter Program to Add/Review: shows in display.
3. Press pad to be programmed or reprogrammed.
• Display will change to review all settings for the pad.
• The pad number that is being programmed displays beside the word
ITEM.
4. Press Time Entry pad to program amount of cooking time.
• Enter desired cooking time by using numeric key pads.
• The total microwave cooking time (all stages combined) is
20 minutes.
5. Press Temp Entry pad to program the cooking temperature.
• Enter desired convection temperature by using numeric
pads.
6. Press Power Level pad to program level of microwave
power.
• For a lower microwave power, press pads 1 (for 10%)
through 9 (for 90%). 0 turns off the microwave power
and cooking is by convection only.
• Press any numeric key pad twice to set power level back to 100%.
7. Press Program Save pad to save the program changes.
8. To discard changes, press Stop/Reset pad.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACP JET519v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACP JET519v3 in the language / languages: English as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ACP JET519v3

ACP JET519v3 User Manual - German - 15 pages

ACP JET519v3 User Manual - Dutch - 15 pages

ACP JET519v3 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info