755883

Abus azwg10001 Manual

33
Zoom out
Zoom in
Previous page
1/118
Next page
33
AZWG10000
8. Operation
8.1 General
The GSM-Interface is normally connected between an analogue telephone line, if
available, and a supplementary device (e.g. alarm system, telephone).
Because of its interface function, it is possible to simulate an analogue telephone
line over the GSM network. The device therefore constantly checks the availability
of the analogue telephone connection (PSTN) and the GSM network.
Normally, all calls and data transmission are transmitted on the primary
transmission line (default: PSTN). If there is a fault in the primary line, messages
are transmitted on the secondary line.
Following every message transmission, the device checks the primary line again.
If the primary transmission line cannot be restored, transmission continues on the
secondary line.
The GSM-Interface has three operating options:
- GSM Backup: Outgoing calls and data transmission are transmitted
primarily on the analogue telephone line. If this is not possible, the device
switches automatically to the GSM network.
- GSM Only: Outgoing calls and data transmission are transmitted over the
GSM network only. This mode is used if no analogue telephone line is
available.
- GSM Main: Outgoing calls and data transmission are transmitted primarily
over the GSM network. If this is not possible, the device switches
automatically to the analogue telephone line.
8.2 Inputs
The GSM-Interface has 4 inputs that you can wire as NC (Normal Closed) or NO
(Normal Open). With the jumper J15, you can select the triggering polarity
(positive/negative).
Each triggering of an input and the reset can be transmitted to each of up to 8
telephone numbers by voice message or text message (SMS).
Each input can be defined as 24h-type (permanently active) or as set/unset
(controlled by SMS commands). This means that, similarly to an alarm system, you
can define when the GSM-Interface reacts to alarms.
Inputs 3 and 4 have additional special functions:
Input 3 can be defined as “PSTN to GSM” type. Here too, the user can send an
SMS command to switch the transmission route from PSTN to GSM.
Input 4 has a so-called abort function, which stops all active dialling actions.
IMPORTANT:
Note that during programming with the GSM software supplied, there can be no
triggering of inputs!
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus azwg10001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus azwg10001 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info