541313

AAS String Studio VS-1 Manual

49
Zoom out
Zoom in
Previous page
1/71
Next page
4.18 The Output Effect Section 49
4.18.1 The Clock Module
This module is used to control the tempo of the different effects of the output section as well as
that of the LFO and Arpeggiator modules. The Source drop down menu is used to determine if
the sync signal comes from an external source or from the internal clock of the module. The Tempo
display indicates the value of the tempo in BPM (beats per minute). When String Studio is used as
a plug-in in a host sequencer and the Ext source is chosen, the clock signal will be that sent by the
host sequencer while in standalone mode the clock will be the one received on the MIDI channel
selected in the toolbar.
When the Int source is chosen, the tempo is determined by the value of Tempo display. The
tempo can also be changed by clicking repeatedly on the Tap pad of the Tempo display which will
update the value of the tempo in the Tempo display.
Note that the settings of the Clock module are saved with presets. In order for the Clock
module to remain in a specific state even when loading new presets, click on the Lock icon at the
top of the module.
4.18.2 The Chorus Module
This module implements both a chorus and a flange effect. It consists of four variable delay lines
in parallel with a cross-feedback matrix between the lines. A wide range of effects is obtained by
modulating the length of the lines and varying the amount of cross-feedback.
The Chorus drop down menu is used to choose between different chorus and flanger algorithms.
The effect can be synchronized to the Clock module with the Sync drop-down menu. Sync values
range from 1/8 of a quarter note (a thirty-second note) to 16 quarter notes (4 whole notes) where
the duration of the whole note is determined by the value (in BPM) appearing in the Tempo display
of the Clock module. The effect can also be synced to a triplet (t) or dotted note (d).
The different chorus algorithms can be controlled with the three knobs appearing at the bottom
of the module. The Mix knob is used to adjust the ratio of “dry” and “wet” in the output signal of
the module. When the knob is adjusted in the left position, only the original or “dry” signal is sent
to the output while in the right position only the processed or “wet” signal is sent to the output. In
its center position there will be equal amounts of “dry” and “wet” signal in the output signal. The
Depth knob is used to adjust the amount of variation of length in the delay lines which controls the
amplitude of the effect while the Rate knob is used to fix the frequency of the modulation.
4.18.3 The Delay Module
This module is a standard ping pong delay which is used to generate echo. It is based on two delay
lines each including a low-pass filter. The effect is obtained by feeding back the signal at the end of
each delay line into the input of the other line with an attenuation coefficient. The result is a signal
traveling from one channel to the other, each time attenuated and filtered in the high frequencies
due to the gain factor and the presence of the low-pass filter.
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AAS String Studio VS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AAS String Studio VS-1 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info