541313

AAS String Studio VS-1 Manual

50
Zoom out
Zoom in
Previous page
1/71
Next page
50 Parameters
The Delay drop down menu is used to choose between different delay algorithms. The effect
can be synchronized to the Clock module with the Sync drop-down menu. Sync values range from
1/8 of a quarter note (a thirty-second note) to 16 quarter notes (4 whole notes) where the duration
of the whole note is determined by the value (in BPM) appearing in the Tempo display of the Clock
module. The effect can also be synced to a triplet (t) or dotted note (d).
The different delay algorithms can be controlled with the three knobs appearing at the bottom
of the module. The Mix knob is used to adjust the ratio of “dry” and “wet” in the output signal of
the module. When the knob is adjusted in the left position, only the original or “dry” signal is sent
to the output while in the right position only the processed or “wet” signal is sent to the output. In
its center position there is equal amounts of “dry” and “wet” signal in the output signal. The Depth
knob is used to adjust the amount of signal re-injected from the output of a line into the other one
while the Rate knob controls the length of the delay lines and therefore the delay between echoes.
4.18.4 The Reverb module
The Reverb module is used to recreate the effect of reflections of sound on the walls of a room or
hall. These reflections add space to the sound and make it warmer, deeper, as well as more realistic
since we always listen to instruments in a room and thus with a room effect.
The Reverb drop down menu is used to choose between different reverb algorithms representing
different types of rooms or halls. Each algorithm can be adjusted with the knobs located at the
bottom of the module. The Mix knob is used to set the relative amount of “dry” and “wet” signal
which is related to the proximity of the sound source. The Decay is used to control the reverberation
time of the room. In a real room, the reverberation time is not constant across the whole frequency
range because the walls of the hall are generally more absorbent at high frequencies which results
in a shorter reverberation time for these frequencies. This effect is controlled with the Color knob
which sets the reverberation time of high frequencies relatively to the value of the Decay knob.
Note that the settings of the different modules of the output stage are saved with presets. In
order for the effects to remain with the same settings even when loading new presets, click on the
Lock icon at the top of the module.
4.18.5 Topology
The three effects of the output section can be used in four different configurations as shown in
Figure 26 and where the Chorus, Delay and Reverb modules are labeled A, B, and C respectively.
Figure 26: The four topologies in which the effects can be applied after the Amp module of the
two module rows; A = Chorus module, B = Delay module and C = Reverb module.
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AAS String Studio VS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AAS String Studio VS-1 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info