503275
69
Zoom out
Zoom in
Previous page
1/126
Next page
Fit the cables in the strain relief.
Continue (see section 7.8.4.4).
7.8.4.4 Connecting solar collector
Note
This sensor must be mounted in the solar collector;refer to the solar collector installation
manual.
Connect the sensor (S1) to the water heater as follows:
Connect the sensor to terminal 2 and 4 of J13.
Fit the cables in the strain relief.
Continue (see section 7.8.4.5).
7.8.4.5 Connecting tank sensor
Note
This sensor is already mounted in the tank prior to delivery. The sensor is mounted
between the inlet and outlet of the heat exchanger. However, you must still connect the
lead to the solar heating system controller.
Connect the lead for sensor S2 with the blade connectors to the sensor.
Connect the other end to terminals 2 and 4 of J14.
Fit the cables in the strain relief.
Continue (see section 7.8.4.7).
7.8.4.6 Connecting top tank sensor
Using the blade connectors, connect the sensor S
3
lead to the sensor.
Connect the other end to terminals 1 and 3 of J14.
Fit the cables in the strain relief.
Continue (see section 7.8.4.7).
7.8.4.7 Connecting communication cable
Note
The communication cable must always be connected, otherwise neither the appliance nor
the solar heating system controller will run.
Connect the double connector to J16.
Fit the cable in the strain relief.
Connect the other end of the communication cable to the terminal block of the
appliance. See
connecting communication cable to the appliance (see section 7.8.4.7).
electrical diagram for the appliance.
electrical diagram for the solar heating system.
Connect the optional Q/T-sensor (see section 7.8.4.8).
If you do not need to make any more connections:
Fit the cover over the controller.
3.
4.
n
1.
2.
3.
n
1.
2.
3.
4.
1.
2.
3.
4.
n
1.
2.
3.
-
-
-
4.
5.
-
0311753_SGS_28-120_II_UKUK_V2.0 , 2017-05-03 69
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGS 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGS 100 in the language / languages: English as an attachment in your email.

The manual is 5,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGS 100

A.O. Smith SGS 100 User Manual - German - 128 pages

A.O. Smith SGS 100 Usermanual and installation guide - Dutch - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info