503275
70
Zoom out
Zoom in
Previous page
1/126
Next page
7.8.4.8 Connecting Q/T sensor
Note
You can optionally add a Q/T sensor to the installation. This enables you to calculate the
energy contribution of the system. For more information or to order the Q/T sensor,
please contact your supplier.
Connect the 5V to J12-1.
Connect sensor S4 to J12-2.
Connect earth to J12-3.
Connect the "flow signal" to J12-4.
Fit the cable in the strain relief.
If you have no more connections to make:
Fit the covers over the controller.
7.9 Commissioning
To commission the water heater:
Fill the water heater (see section 7.9.1)
Check the supply pressure (see section 7.9.2)
Check the gas control valve pressure
Measure the CO
2
(see section 7.9.4)
Switch pressure measurement (see section 7.9.5)
Turn on the water heater (see section 7.9.6)
7.9.1 Filling
7.9.1.1 Filling unvented installations
Refer to the installation diagram when you fill the water heater:
Open the stop valve (11) in the hot water supply pipe.
If applicable, open the stop valves (4) of the circulation pipe (C).
Make sure that the drain valve (9) is closed.
Open the nearest hot water draw-off point (14).
Open the stop valve (4) of the cold water supply pipe (A). Cold water flows into the
water heater.
Fill the water heater until a full water jet flows from the nearest draw-off point. The
water heater is completely full.
Open all draw-off points to bleed the entire installation of air.
The water heater is now under water supply pressure.
Make sure that no water comes out of the expansion valve (15) or the T&P valve (3).
If water comes out:
Examine if the water supply pressure is greater than the specified value in the
Technical details. If necessary, install a pressure reducing valve (1).
Examine if the expansion valve in the protected cold supply set-up is installed
correctly and is not defect. If necessary, replace the expansion valve.
7.9.1.2 Filling vented installations
To fill the water heater, proceed as follows:
Open the stop valve (11) in the hot water pipe and, if present, the stop valves (4) for
the circulation pump (6).
Close the drain valve (9).
Open the nearest hot water draw-off point (14).
Open the stop valve (4) on the cold water side (A) so that cold water flows into the
water heater.
Completely fill the water heater. When a full water jet flows from the nearest draw-
off point, the water heater is full.
Bleed the entire installation of air, for example by opening all draw-off points.
n
1.
2.
3.
4.
5.
6.
-
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
7.
8.
-
-
1.
2.
3.
4.
5.
6.
70 Installation, Maintenance and Service part
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGS 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGS 100 in the language / languages: English as an attachment in your email.

The manual is 5,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGS 100

A.O. Smith SGS 100 User Manual - German - 128 pages

A.O. Smith SGS 100 Usermanual and installation guide - Dutch - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info