503225
71
Zoom out
Zoom in
Previous page
1/118
Next page
Switch on the power to the appliance using the isolator on the appliance.
Switch the controller ON by setting the 0/I switch
to position I.
The display will now show INTERNAL CHECK for about 10 seconds, and will then go
to the main menu.
Select SERVICE OPERATION, FULL LOAD from the service menu.
Confirm with [ENTER].
The display shown here will appear
The appliance is now in Full load mode and will ignite.
You must wait about 1 minute after the display shows the text RUNNING before
reading the dynamic pressures (the fan needs this time to get up to full speed, so
that you can get a reliable reading).
Use the pressure gauge to read the supply pressure and compare it against the value
from the gas table.
Note
Consult the mains gas supply company if the supply pressure is not correct.You cannot
yet start using the appliance. You must now take the appliance out of service (see section
4.2.2).
Note
After conversion, you must check that the gas control valve is gastight.
Shut off the gas supply.
Disconnect the pressure gauge and retighten the sealing screw in the test nipple.
If there is nothing else you need to check or adjust, you can put the covers back on
the appliance.
7.9.3 Procedure for checking the gas control valve pressure
The procedure for checking the gas control valve pressure is only applicable to appliances
that have a pressure-reducing valve. If the appliance does not have a reducing valve,
continue from adjusting the CO
2
value (see section 7.9.4).
To check the gas control valve pressure, proceed as follows:
Isolate the appliance from the power supply (see section 4.2.2).
Carefully remove the covers from the appliance.
The electrical section is now visible.
The gas control valve has a test nipple that can be used for measuring the gas
control valve pressure. This test nipple has a sealing screw. Loosen the sealing screw
by a few turns. Do not completely loosen it as it can be difficult to retighten.
Open the gas supply.
Connect a pressure gauge to the test nipple.
Switch on the power to the appliance using the isolator on the appliance.
Switch the controller ON by setting the 0/I switch to position I .
7.
8.
9.
10.
11.
12.
n
13.
14.
15.
1.
2.
3.
4.
5.
6.
7.
8.
0311732_SGE_40-60_II_UKUK_V2.0 , 2017-05-03 71
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGE 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGE 60 in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGE 60

A.O. Smith SGE 60 User Manual - German - 120 pages

A.O. Smith SGE 60 User Manual - Dutch - 114 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info