503225
70
Zoom out
Zoom in
Previous page
1/118
Next page
Filling with glycol
Insert the hose of the glycol pump into the jerry can containing the glycol.
Connect the pump to the jerry can.
Connect the hose of the glycol pump to the inlet combination of the pump station.
Open the valve of the inlet combination.
Plug the glycol pump into a mains socket.
Start the glycol pump using the ON/OFF switch on the glycol pump.
Stop the glycol pump as soon as the pressure gauge on the pump station begins to
rise.
Completely bleed the system of air at the air bleed point (26, see installation
diagram).
Close the air bleed when no further air comes out.
Use the service menu to switch the pump on (see section 9.2.9.2).
Note
To ensure that the solar heating system is properly filled, the pump in the solar heating
system can be switched on for 2 minutes using the service menu.
Repeat steps 6 through 9 until glycol runs out of the air bleed (26).
Note
If an installation does not have a drain-back system, then it should be filled up to
pressure (1.5 bar).
If an installation does have a drain-back system, then it should not be pressurised. For
the installation, filling and drainage of a drain-back system, please refer to the installation
manual and users manual of the solar collectors.
Switch off the glycol pump.
Close the valve of the inlet combination and disconnect the glycol pump (including
the hoses).
Note
Dispose of the residual glycol in the filler hose in an environment-friendly manner, and
according to local regulations.
7.9.2 Procedure for checking the supply pressure
To check the supply pressure, proceed as follows:
Isolate the appliance from the power supply (see section 4.2.2).
Carefully remove the covers from the appliance.
The electrical section is now visible.
There is a test nipple before the gas control valve (for natural gas appliances) or
before the pressure-reducing valve (for LPG appliances) so that the supply pressure
can be measured.
This test nipple has a sealing screw. Loosen the sealing screw by a few turns. Do not
completely loosen it as it can be difficult to retighten.
IMD-1095aR0
IMD-1096aR0
Open the gas supply and vent the gas supply line via the test nipple.
Connect a pressure gauge to the test nipple as soon as gas starts to flow from it.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
n
11.
12.
13.
1.
2.
3.
4.
5.
6.
70 Installation, Maintenance and Service part
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGE 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGE 60 in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGE 60

A.O. Smith SGE 60 User Manual - German - 120 pages

A.O. Smith SGE 60 User Manual - Dutch - 114 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info