503225
73
Zoom out
Zoom in
Previous page
1/118
Next page
Place the CO
2
meter's measurement probe in the test nipple (58) of the flue gas
outlet pipe (the number is a reference on the General working principle of the water
heater (see section 5.1)).
Open the gas supply and vent the gas supply line.
Use the main switch to apply mains voltage to the appliance.
Start the appliance (see section 4.1).
Go to the [ ] SERVICE OPERATION menu.
Generate a heat demand by draining the appliance until it is cold or by raising the
value for T
set
in the SERVICE menu. Use [ ]
for this.
Full load measurement
From the service menu, select:
SERVICE OPERATION | FULL LOAD
Confirm with [ENTER].
The appliance is now in FULL LOAD mode and will ignite.
The appliance is now running at FULL LOAD. Read the value from the CO
2
meter
and wait until this measured value has remained stable for some time. This may take
several minutes.
Then compare the measured CO
2
value against the value from the table.
The CO
2
value at full load must be within ±1.0 vol% of the CO
2
value stated in the
table.
If necessary, adjust the CO
2
value using the adjuster screw until the value is within
the range listed in the table of CO
2
values.
Use the Allen key supplied for this. The key can be found in the plastic bag that is
attached to the appliance.
Fig. CO
2
adjustment (full load)
IMD-1095bR0
Note
Turning to the left (anticlockwise) means more gas (higher CO
2
level) and turning to the
right (clockwise) means less gas (lower CO
2
level).
Note
Note
After conversion, you must check that the gas control valve is gastight.
If you have increased T
set
, set it back to the original value using [ ].
Continue with the CO
2
measurement under partial load.
4.
5.
6.
7.
8.
9.
10.
-
-
11.
12.
13.
n
14.
15.
0311732_SGE_40-60_II_UKUK_V2.0 , 2017-05-03 73
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGE 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGE 60 in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGE 60

A.O. Smith SGE 60 User Manual - German - 120 pages

A.O. Smith SGE 60 User Manual - Dutch - 114 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info