671757

A.O. Smith BTI 100 Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
19
18
2.5 Temperature regulation
The appliance is under water supply
pressure (maximum 8 bar). The amount
of cold water that is added is equal to
the amount of hot water used. The gas
control block automatically regulates the
gas supply. The main burner will ignite as
soon as a reduction in water temperature
is sended by the thermostat. The main
burner will shut down as soon as the
preset temperature is achieved.
At high water temperatures there is more
scale buildup in the appliance. It is for
this reason that it is recommended to
place the temperature control knob in
position of 60 °C as the accumulation of
scale will be reduced.
2.6 Converting to another
type of gas
For conversion of the appliance from
natural gas to another type of gas, or
visa versa, it is necessary to exchange
the pilot injector and the main injector.
The conversion may only be executed by
a qualed competent person.
Procedure:
1. Shut the heater down. Close the main
inlet gas valve and switch off the
electricity supply at the main switch;
2. Remove the burner assembly;
3. Replace the injectors with the correct
injectors from the conversion set.
(see table below).
Remark:
- When conversion of the appliance
from natural gas to another type of
gas, x the screw on the gas block
of the burner pressure control as
far as the stop.
- When conversion of the appliance
from another type of gas to natural
gas, then the right burner pressure
should be adjust.
2.7 Maintenance
To ensure safe and efcient operation of
the water heater it is recommended that
it is cleaned and serviced at least once a
year by a qualied competent person.
2.7.1 Magenesium anode
The life cycle of the anode is determined
by the quality and the quantity of the
water owing through the water heater.
It is therefore recommended that the
anode be inspected and replaced if
necessary at least once a year.
1. Close the stop cock in the cold water
supply pipe;
2. Open the nearest hot water tap in
order to allow the pressure to drop
from the water heater and the pipes;
3. Slacken the anode with a tting
wrench;
4. Check the anode and replace it if it
has been reduced in diameter by 60%
or more at any point on its lenght;
5. Check for water leaks.
If is necessary to replace the anode it
should be replaced by one of the same
type. The type of anode required can be
detemined on the basis of the type of the
appliance and the serial number.
2.7.2 Cleaning
1. Close the gas supply and demount
the burner after it has cooled down
2. Disconnect the burner assembly from
the gas control
3. Remove the complete burrner
assembly
4. Clean the burner with a soft brush
5. Check the pilot burner and clean it if
so required
6. Check the combustion chamber, ue
tube and ue bafe and clean these if
required
After cleaning of the pilot- and main
burner the operation of these should
be checked. If necessary the burner
pressure should be reset.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith BTI 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith BTI 100 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info