534678

3Dprintingsystems UP Plus Manual

31
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
3.3.5
Preparing the Platform
Before printing, the platform must be prepared so
be printed without the model moving.
front of the Perfboard onto
the platform.
it will cause the
Perfboard to warp as well, in these cases you will need to use more clips to hold it
down.
The P
erfboard is cut at 45 degrees angle with the edge, and just fits the size of the platform. When
printing starts, plastic will have more chance to be pushed
stronger mechanical bond with the bottom surface that prevents it from later lifting.
Cleaning the Perfboard
To clean the platform,
use the i
and simply just scrape off the surface plastic until smooth on both sides. If you preheat the
form
for longer the plastic left in the Perfboard
to it, thus not requiring the holes of t
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
Preparing the Platform
Before printing, the platform must be prepared so
that the
model adheres to the platform enough to
be printed without the model moving.
Use the clips in the box provided,
these are
the platform.
For large models the warping force can be so strong that
Perfboard to warp as well, in these cases you will need to use more clips to hold it
erfboard is cut at 45 degrees angle with the edge, and just fits the size of the platform. When
printing starts, plastic will have more chance to be pushed
into all perforations, and this provides a
stronger mechanical bond with the bottom surface that prevents it from later lifting.
use the i
ncluded red Perfboard pokers.
The preference is to
and simply just scrape off the surface plastic until smooth on both sides. If you preheat the
for longer the plastic left in the Perfboard
holes
becomes soft and the extruded plastic sticks
to it, thus not requiring the holes of t
he Perfboard to be empty/clean.
Troubleshooting
model adheres to the platform enough to
these are
used to clip the
For large models the warping force can be so strong that
Perfboard to warp as well, in these cases you will need to use more clips to hold it
erfboard is cut at 45 degrees angle with the edge, and just fits the size of the platform. When
into all perforations, and this provides a
stronger mechanical bond with the bottom surface that prevents it from later lifting.
The preference is to
use the spatula
and simply just scrape off the surface plastic until smooth on both sides. If you preheat the
plat-
becomes soft and the extruded plastic sticks
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info