533782

Zoom MRS-802 Manual

181
Zoom out
Zoom in
Previous page
1/184
Next page
Creating a CD using the disc-at-once method
ZOOM MRS-802 Ver 2.0
9
●
To switch the V-take for the master track
Press the [EXIT] key repeatedly to return to the main
screen. Load the project for which you want to switch
the V-take, and select the V-take for the master track.
Then return to the album screen.
11.
When you have stored all desired projects
in the album, press the [ENTER] key twice.
The display indication changes as follows.
HINT
If you press the [ENTER] key once more, the indication “CD
xx Trk BURN?” (where xx is the number of tracks) appears on
the display. You can check the total number of tracks that will
be written to the disc from this screen.
12.
To carry out the write process, press the
[ENTER] key once more.
By pressing the [EXIT] key instead of the [ENTER] key,
you can cancel the operation and back up one step at a
time. When you start the write procedure, the display
shows “wait...” for track-at-once or “init...” for disc-at-
once. The counter indicates the progress status of the
write process.
When the write process is completed, the disc is ejected
automatically, and the message “ALBUM NEXT?”
appears on the screen. To write another disc with the
same content, insert a blank CD-R/RW disc or a CD-RW
disc which has been completely erased, and press the
[ENTER] key. To terminate the process, press the [EXIT]
key.
13.
To return to the main screen, press the
[EXIT] key several times.
When you create an audio CD using the disc-at-once
method, marker information included in the project can
be used to generate PQ subcode information (specifying
track start/stop position and other items) to split up a
single project into multiple tracks. Marker-based track
separation can be enabled or disabled for each project.
For example, when a project contains a number of songs
that were recorded live, you can set a mark at the
beginning of each song, so that these will be recorded as
different tracks on the CD. This will enable easy
searching and jumping between tracks.
NOTE
To use the marker-based track separation function, at least
two marks (including the project start mark 00) must be set.
1.
Load the project that you want to split into
multiple tracks, and set marks at the points
where the tracks should be separated.
Marker-based track separation can only be enabled or
disabled for the entire project. Delete any unnecessary
marks beforehand.
2.
Perform steps 1 - 6 of “Creating an audio
CD by album”, select the disc-at-once
(DAO) write method, and bring up the
album screen.
3.
Use the cursor left/right keys and the dial to
register projects for the album.
4.
Use the cursor left/right keys to select a
project that is to be divided into multiple
tracks.
5.
Press the [MARK] key in the control
section.
Marks contained in this project will be used as PQ
subcodes. The indication “PQ” is shown at the top right
of the display.
By pressing the [MARK] key again, you can return to the
ALBUM
ALBUM
SURE?
SURE?
Using the marker function to
separate tracks
END OF
END OF
PROJECT
PROJECT
0 0 0
1
MRS802v2(E).fm 9 ページ ２００４年５月２７日　木曜日　午後５時５９分
… 181 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom MRS-802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom MRS-802 in the language / languages: English as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zoom MRS-802

Zoom MRS-802 User Manual - German - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info