Manual Zoom G2.1u (page 14 of 23) (English)

629753

Zoom out

Zoom in

1/23

ZOOM G2.1u

Effect Types and Parameters

DELAY

DELAY module

This is a delay module which allows long delay times and use of the hold function.

DELAY

This is a delay with a maximum setting of 5000 ms.

PINGPONG DELAY

This is a ping-pong type delay where the delay sound alternates between left and right.

ECHO

This effect simulates a tape echo with a long delay time of up to 5000 ms.

These three effect types have the same parameters.

TIME

1 – 99,

1.0 – 5.0

FEEDBACK

0 – 98, 1.0

MIX

0 – 98, 1.0

Adjusts the delay time. In the

range from 10 – 990 ms, the

adjustment is made in 10-ms

steps (1 – 99). For 1 second and

above, the adjustment is made in

100-ms steps (1.0 – 2.0).

Adjusts the feedback amount.

Adjusts the mixing ratio of

original sound and ef

fect sound.

HOLD

TAP

Effect parameters 1 – 3

Effect type

These are the parameters that can be adjusted with Parameter knobs 1 – 3 when

the effect type is selected. The setting range for each parameter is shown.

Three-digit setting values are shown with a dot between the two numerals.

Example: 1 – 98, 1.0 = 1 – 98, 100

Expression pedal

A pedal icon ( ) in the listing indicates a parameter that can be controlled with the expression

pedal (FP01/FP02).

Specify the respective module as modulation target for the expression pedal (→ p. 20), and then

select the respective effect type of the module. The parameter can then be controlled in real time

with a connected expression pedal.

Tap

A [TAP] key icon ( ) in the listing indicates a parameter that can be set by hitting the [TAP]

key.

In edit mode, when the respective module/effect type is selected, repeatedly hitting the [TAP] key

will set the parameter according to the key press interval (modulation cycle, delay time, etc.).

In play mode, if the DELAY module is ON for the currently selected patch, repeatedly hitting the

[TAP] key will temporarily change the parameter.

Hold

A foot switch icon ( ) in the listing indicates an effect type for which hold can be turned

on and off with the foot switch (FS01).

Set the foot switch function to "dH" (delay hold) (→ p. 22) for the respective patch. When this patch

is then selected in play mode, the hold function can be switched on and off by pressing the foot

switch.

Module selector

The Module selector

symbol shows the

position of the knob at

which this

module/parameter is

called up.

Effect module

TAP

HOLD

How to read the parameter table

Effect Types and Parameters

ZOOM G2.1u

COMP

COMP (Compressor) module

Attenuates high-level signal components and boosts low-level signal components,

thereby keeping the overall signal level within a certain range.

SENSE

0 – 10

ATTACK

FS, SL

LEVEL

2 – 98, 1.0

Adjusts the compressor sensitivity.

Higher setting values result in higher

sensitivity.

Selects compressor attack speed in two

levels. Available settings are "FS" (fast)

and "SL" (slow).

Adjusts the signal level after passing the

module.

WAH/EFX

WAH/EFX (Wah/Effects) module

Comprises wah and ﬁlter effects as well as VCA type effects.

AUTO WAH

This effect varies wah in accordance with playing intensity.

AUTO RESONANCE

This effect varies the frequency band of the resonance ﬁlter according to the picking intensity.

The two effect types above have the same parameters.

POSITION

bF, AF

SENSE

-10 – -1, 1 – 10

RESONANCE

0 – 10

Selects the connection position of the

WAH/EFX module. Available settings

are "bF" (before DRIVE module) and

"AF" (after EQ/EXTRA EQ module).

Adjusts the effect sensitivity.

Adjusts the resonance of the sound.

BOOSTER

Raises signal gain and creates a dynamic sound.

RANGE

1 – 5

TONE

0 – 10

LEVEL

2 – 98, 1.0

Selects the frequency band that is

boosted.

Adjusts the sound quality.

Adjusts the signal level after

passing the module.

TREMOLO

This effect periodically varies the volume.

DEPTH

0 – 98, 1.0

RATE

0 – 50

WAVE

u0 – u9, d0 –

d9, t0 – t9

Adjusts the modulation depth.

Adjusts the effect rate.

Allows selection of the modulation

waveform. Available settings are "u"

(rising sawtooth), "d" (falling sawtooth),

and "t" (triangular). Higher setting

values result in more clipping of wave

peaks, which reinforces the effect.

PHASER

This effect produces sound with a pulsating character.

POSITION

bF, AF

RATE

0 – 50

COLOR

1 – 4

Selects the connection position of the

WAH/EFX module. Available settings

are "bF" (before DRIVE module) and

"AF" (after EQ/EXTRA EQ module).

Adjusts the modulation rate.

Adjusts the type of sound.

TAP

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zoom G2.1u in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zoom G2.1u Manual

Product: