629753
12
Zoom out
Zoom in
Previous page
1/23
Next page
Use of Expression Pedal/Foot Switch
ZOOM G2.1u
22
2. Set the Module selector to the
"CONTROL" position.
The G2.1u goes into edit mode. You can now
make settings for the expression pedal or foot
switch.
3. Turn Parameter knob 2 to select one
of the following functions for the foot
switch.
bP (bypass/mute)
The foot switch controls bypass or mute on/off.
This has the same effect as pressing both [W]/
[Q] foot switches at the same time in play
mode.
tP (tap tempo)
Pressing the foot switch repeatedly can be used
to set the interval for the rhythm function or to
make settings for effect parameters supporting
the tap function. This has the same effect as
pressing the [TAP] key.
bU (bank up)
Each push of the foot switch switches to the
next higher bank. This has the same effect as
pressing the BANK [+] key.
rH (rhythm on/off)
The foot switch controls start/stop of the
rhythm function. This has the same effect as
pressing the RHYTHM [R/P] key.
dH (delay hold)
The foot switch controls on/off of the delay
hold function. When a patch using the hold
function is selected, pressing the foot switch
will activate hold, causing the current delay
sound to be repeated (see illustration at the
bottom of this page). Pressing the foot switch
once more cancels the hold condition, and the
delay sound will decay normally.
dM (delay input mute)
The foot switch controls muting on/off for the
delay module input signal.
HINT
For information on effect parameters supporting the
tap function, see pages 27 – 33.
To use the hold function, an effect type that
supports the hold function must be selected in the
patch. For details, see page 34.
•While the delay module is set to hold or mute, the
dot in the center of the display flashes.
4. Select the patch in play mode and
operate the foot switch.
The selected function will be activated.
This function applies to all patches.
Using the G2.1u as audio
interface for a computer
By connecting the [USB] connector of the G2.1u
to a computer, the G2.1u can be used as an audio
interface with integrated AD/DA converter and
Foot switch pressed
Pressed again
Original sound
Delay sound
Hold
Use of Expression Pedal/Foot Switch
ZOOM G2.1u
23
[USB]
[USB]
[INPUT]
USB
USB
DAW
application
DAW
application
Effects
Effects
G2.1u
Record
G2.1u
[INPUT]
[OUTPUT]
[OUTPUT]
Playback
effects. The operating environment conditions
for this type of use are as follows.
Compatible operating system
Windows XP
MacOS X (10.2 or later)
Quantization
16-bit quantization
Sampling frequency
32 kHz / 44.1 kHz / 48 kHz
HINT
With each of the operating systems listed above, the
G2.1u will function as an audio interface simply by
connecting the USB cable. There is no need to install
any special driver software.
To use the G2.1u as an audio interface for the
computer, connect the [USB] connector of the
G2.1u to a USB port on the computer. The G2.1u
will be recognized as an audio interface.
HINT
If the [POWER] switch of the G2.1u is set to OFF,
power will be supplied via the USB connection.
If the [POWER] switch of the G2.1u is set to ON,
power will be supplied from the batteries in the
G2.1u or the AC adapter. Care should be taken
especially when running on battery power,
because setting the switch to ON may result in
faster depletion of the batteries.
In this condition, the sound of a guitar connected
to the [INPUT] jack of the G2.1u can be
processed with the effects of the G2.1u and then
recorded on the audio tracks of a DAW (Digital
Audio Workstation) software application on the
computer.
At the same time, the [OUTPUT] jack of the
G2.1u carries the playback sound from the audio
tracks of the DAW application, mixed with the
guitar sound processed by the effects of the
G2.1u.
For details on recording and playback, refer to
the documentation of the DAW application.
NOTE
Also when using the G2.1u as an audio interface,
the signal after effect processing is always
available directly at the [OUTPUT] jack.
If the DAW application has an echo back function
(input signal during recording is supplied directly to
an output), this must be disabled when using the
G2.1u. If recording is carried out with this function
enabled, the output signal will sound as if
processed by a flanger effect.
Use a high-quality USB cable and keep the
connection as short as possible. If power is
supplied to the G2.1u via a USB cable that is more
than 3 meters in length, the low voltage warning
indication may appear.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom G2.1u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom G2.1u in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info