781890
19
Zoom out
Zoom in
Previous page
1/24
Next page
19 І 24
side but is removed by the extraction system. Make
sure before each operation with this power tool that
the brush edge (10) is not damaged. Have it replaced
if there is damage or wear.
Connection to the power supply
1. Make sure that the power tool is switched off. Always
switch the on/off switch (3) to off position before con-
necting the power tool to the power supply.
2. Plug the power plug into a correctly installed socket
which camplies with the requirements specied in the
technical data.
3. Your power tool is now ready for operation.
Operation
Oscillation rate
Before you start working with the swing speed to match
the appliance. Use a low swing speed for coarse grind-
ing, increase the oscillation rate for ne work.
1. Rotate the adjustment wheel (6) to adjust the oscilla-
tion rate. Turn the wheel clockwise to reduce the os-
cillation rate (Fig.9).
2. Turn the wheel counter-clockwise to increase the os-
cillation rate (Fig. 10).
Switching on/off
To switch on:
Push the on/ off switch (3)
Continuous operation: (Fig.11)
Secure the on/off switch (3) with the Ieeking button (a)
To switch off:
Press the on/off switch (3) briey.
Note: The insertion tool moves for a short while after
having it switched off. Do not put aside the power tool
until the insertion tool has come to a complete halt.
Grinding
1. Attach an appropriate abrasive sheet (13) and select
the corresponding speed.
2. Hold the power tool securely at the handle surfaces
(1, 2) and switch it on as described.
3. Wait until the insertion tool has reached its full operat-
ing speed.
4. Hold the grinding plate (9) as parallelas possible to
the wall, and touch the surface tobe processed with
the brush edge (10) rst.
5. Apply some pressure to the grinding head (8) such that
the insertion tool touches the surface to be processed.
6. Constantly move the power tool over the surface.
Note: lf you want to avoid irregular grinding results, do
not keep the power tool at one spot for too long.
7. Lift the grinding plate (9) from the surface to be pro-
cessed before switching off the power tool.
8. Do not put aside the power tool until the insertion tool
has come to a complete halt.
Sandpaper
Selection
1. The grain size of the sandpaper is specied on its rear
side. The smaller the specied number, the coarser
the graining.
2. Use sandpaper with coarse grain for rough grinding,
and sandpaper with ne grain for nishing. We re-
cornrnend sandpapers with aluminium oxide, silicon
carbide or other synthetic abrasives.
3. lf you can chose between sandpapers with different
graining, you should start with coarsegraining sandpa-
per and complete the grinding process with the nest
possible graining. Thus you will get good and smooth
grinding results.
How to apply and replace sandpaper
Apply the sandpaper (13) to the grinding plate (9) using
the Velcro strip mechanism.
1. Align the sandpaper (13) with the grinding plate (9)
and press it on evenly.
2. PuII the sandpaper (13) off the grinding plate (9) and
replace it with a new one I another one (Fig.5).
Dust extraction
WARNING! Harmfull noxious gases may be generated
when e.g. lead-containing paint is processed. These
gases entail a risk for the operator and the persons in
the vicinity!
Therefore only use the power tool in combination with
a dust extraction unit, and protect yourself and other
persons in the working area with additional suitable per-
sonal protective equipment!
When working with this power tool, a Iot of dust is gener-
ated. The dust extraction unit is very useful if you want
to keep your workplace clean. lt is possible to combine
the extraction system or a vacuum cleaner with the ex-
traction hose (11) which is connected to the adapter for
dust extraction.
1. Align the nose at the hoseend with the extraction hose
adapter (12) (Fig.3), insert the end and secure it by
turning in a clockwise rotation (Fig.7).
2. Connect the dust extraction adapter with a suitable
dust extraction unit such as a vacuum cleaner (Fig.8).
Note: Make sure that the vacuum cleaner is suitable for
being used tagether with a power tool.
Brush edge
The grinding head of this power tool is enclosed by a brush
edge (1 0) which offers the following two advantages:
a) The brush edge (1 0) protrudes beyond the grinding
plate (9) and touches the surface to be processed
rst. Thus, the grinding plate is positioned in parallel
to the working area before the insertion tool comes in
contact with the surface which is to be processed. This
is to prevent the formation of sickle-shaped recesses
caused by the grinding disk edge.
b) Furthermore, the brush edge (10) prevents the gen-
eration of excessive dust. Dust generated du ring the
grinding process is not transported towards the out-
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zgonc YPL 710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zgonc YPL 710 in the language / languages: English, German as an attachment in your email.

The manual is 2.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info