781884
31
Zoom out
Zoom in
Previous page
1/36
Next page
31GB
Maintenance
If personnel qualied for unusual main-
tenance tasks or repairs must be ob-
tained during of after the warranty pe-
riod, please always contact a service
point recommended by us or contact
the manufacturer.
Only perform repair, maintenance and
cleaning work as well as the correction
of malfunctions with the drive switched
off as a basic rule.
All protective and safety equipment must
be reassembled immediately after repair,
maintenance is completed.
CLEANING
Caution! Disconnect the mains plug.
Clean the machine each time after com-
pleting work.
The machine should be cleaned regularly
to remove dust and dirt.
Keep safety devices, air vents and the
motor housing as dust and dirt-free as
possible.
Clean the device with a clean cloth, or
blow it out with compressed air at low
pressure.
All moving parts are to be re-greased at
periodic intervals.
Do not use detergents or solvents as
these might damage the plastic parts of
the device. Make sure that no water can
get inside the device.
Carbon brushes
In case of excessive sparking, have the
carbon brushes checked by a qualied
electrician.
Caution! The carbon brushes should be re-
placed only by a qualied electrician.
Check the oil level
The oil level should be checked before
each use of the device.
Place the device with the tool holder in the
down position on the oor. The oil must be
aligned with the marked cross. Rell with oil
if necessary.
Oil change: Fig.5
The oil should be changed after about 40-
50 hours of operation.
Recommended oil: 30 ml SAE 15W/40 or
similar.
Caution! Switch off the device. Discon-
nect the mains plug!
1. Lay the device on its back. Unscrew the
sight glass (4) by opening the four tap-
ping screws (11).
2. Empty the old oil by tilting it into a suit-
able container.
Note: Waste oil must be disposed of
at the appropriate collection point for
used oil!
3. Fill in the new oil (about 30 ml) into the
oil ller opening.
4. Tighten the sight glass again and check
the oil level. Rell or remove oil if nec-
essary.
5. Check the oil level again after a short
period.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zgonc YPL 1900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zgonc YPL 1900 in the language / languages: English, German as an attachment in your email.

The manual is 1.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info