529864
80
Zoom out
Zoom in
Previous page
1/104
Next page
USER MANUAL
ENGLISH/ GERMAN
USER MANUAL
BEDIENUNGSANLEITUNG
ZE
-
N C 315 2
CAR SPECIFIC NAVICEIVER FOR
AUDI TT VEHICLES
2
CONTENTS
SAFETY INSTRUCTIONS .....................................................................................3
FRONT PANEL BUTTONS ................................................................................. 4-5
OPERATION OF STEERING WHEEL CONTROLS ........................................... 6-7
BASIC OPERATION ...........................................................................................8-9
RADIO MODE .................................................................................................10-13
PLAYBACK OF A/V SOURCES .....................................................................14-19
BLUETOOTH MODE ......................................................................................20-27
NAVIGATION MODE .......................................................................................28-29
SYSTEM SETUP ............................................................................................. 30-39
REMOTE CONTROL MAIN ............................................................................40-41
REMOTE CONTROL M-ZONE .......................................................................42-43
EXTERNAL PLAYBACK AND SOURCES .....................................................44-45
GLOSSARY..........................................................................................................46
TROUBLESHOOTING .................................................................................... 47-48
SPECIFICATIONS ................................................................................................ 49
WARRANTY .................................................................................................... 98-99
EC DECLARATION OF CONFORMITY ............................................................ 102
ƽ Navigation manual is separate.
3
ZE
-
N C 3 15 2
SAFETY INSTRUCTIONS
1. Read these instructions entirely.
2. Keep these instructions within reach. Whoever uses the unit should have access to this manual.
3. Heed all warnings. Follow the instructions.
4. This unit is designed to be used in a vehicle with 12V DC battery and negative ground.
5. Do not operate the unit in any other way than described in this manual. Failure to follow the
instructions within this manual may void your warranty.
6. Do not disassemble or alter the unit in any way, because it will void your warranty. Do not attempt to
repair or to service the unit yourself, but contact an authorized ZENEC dealer instead.
7. Use only original accessories which are designed and manufactured for the unit, otherwise you
will risk damage. Install the unit according to the mounting manual, using the supplied mounting
accessories. The forces of acceleration for accidents are sometimes huge. Incorrect mounted units
are a big risk for the driver and the car passengers, during an accident.
8. Protect the unit from water and other liquids, which can enter the casing. A short circuit or even fire
could be the result.
9. To prevent a short circuit, never insert or stick any metallic objects (such as coins or metal tools) into
the unit.
10. Before you replace a defective fuse, try to find the cause for the short circuit. Please pay attention
to the cables of the power supply! If the short circuit doesn't result from a failure of the power supply
or wiring, you can replace the defective fuse with a new one (same values). If the short-circuit is still
existing, please contact an authorized ZENEC dealer.
11. When connecting to any other device, read its user's guide for detailed safety instructions. Do not
connect incompatible products.
12. Be careful not to drain the car battery while using the unit when the car engine is turned off. Because
the unit uses a considerable amount of energy and the battery will be charged only while the engine
is running, it might happen that the battery will discharge to a point where it's not longer possible to
start the engine.
13. According to the law in different European countries, driving with monitors which are showing
movies in the viewing range of the driver is not allowed, because the driver might be distracted from
the traffic. Please respect the traffic regulations of your country, or you might face penalties in case
of an accident or even loose your insurance coverage. Please pay attention to the volume inside
your vehicle, because you are obliged to notice exterior sounds like police sirens etc.
14. Don't expose the unit to hard impacts. A mechanical or electrical malfunction of the unit could be the
result.
15. Should any problems or questions occur during installation, please consult your ZENEC dealer/
importer.
16. This unit utilizes a class 1 laser. Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous exposure to coherent light. Do not open covers
and do not repair yourself. Refer servicing to qualified personnel.
4
FRONT PANEL BUTTONS
Front Panel
5
ZE
-
N C 3 15 2
1. IR RECEIVER
2. DISC INDICATOR
3. DISC SLOT
4. EJECT
Eject disc
5. HOME
Press to open Main Menu,
hold to open EQ page
6. FM/AM
Press to switch to FM/AM source
Press and hold to de- and activate
TA function
7. PWR/VOL
Rotate to increase/decrease volume,
press and hold to switch device
ON/OFF
8. DVD
Press to switch to DVD source
9. NAV
Press to switch between Navigation
and playback page
Press and hold to fade in/out the
infobars manually
10. INTERNAL MICROPHONE
11. PASSANGER AIR BAG INSERT
No function for ZE-NC3152, see
mounting instructions for detailed
information
12. SD CARD SLOT
13. RESET
Press to initiate a hardware reset
14. BT
Press to switch to BT source
15. NEXT
Press to choose next
Track|Chapter|Station
Press and hold to fast forward
16. SMART DIAL
Rotate to move a cursor up and
down
Press to confirm a selection
17. PREVIOUS
Press to choose previous
Track|Chapter|Station
Press and hold to fast rewind
18. ALT
Funktion can be set in Setup
Press and hold to open the Video
setup
FRONT PANEL BUTTONS
FRONT PANEL BUTTONS
6
OPERATION OF STEERING WHEEL CONTROLS
7
ZE
-
N C 3 15 2
OPERATION OF STEERING WHEEL CONTROLS
OPERATION OF STEERING WHEEL CONTROLS
1. NEXT
Rotate up to choose next
Track | Chapter | Station
2. SCAN | FAST FORWARD
Press to scan for next FM station
Press and hold for fast forward action
3. PREVIOUS
Rotate down to choose previous
Track | Chapter | Station
4. MODE
Press to choose next playback source
5. TELEPHONY
Press to answer or hang up a call
Press and hold to reject an incoming call
6. VOL/MUTE
Rotate to increase/decrease volume
Press to mute/unmute audio
8
BASIC OPERATION
SELECT A SOURCE
Enter main menu:
- Via Touchscreen:
Touch the icon in the upper left corner of the screen.
- Via "HOME" button:
Push "HOME" button to enter main menu.
Operation at main menu:
The main menu consists of three pages: 2 main pages and 1 M-Zone page.
There are two basic ways to get there:
- Slide You can slide the two main pages back and forth.
Just slide your fingertip onscreen in the respective direction.
The M-Zone page (backseat area) cannot be accessed
via sliding.
- Bar Tap on any of the three rectangular markers in the top area of the
screen to navigate through all three main menu pages. M-Zone
included.
Entering the main menu you have access to all playback sources and settings.
ADJUST LOCAL LANGUAGE
Tap center header button or slide to second main menu page. Choose SETUP
> GENERAL > LANGUAGE and adjust to your likings. You might want to adjust
some other basic settings. See chapter "Setup".
POWER ON/OFF
Main menu 1 Main menu 2 M-Zone page
Correctly installed, your device will power on together with the ignition of the vehicle.
Ignition off: Device does not receive power. When the ignition is activated, you may
also switch the device On and Off using the front panel power button.
9
ZE
-
N C 3 15 2
BASIC OPERATION
BASIC OPERATION
Display & control elements:
Indicates current source
- Tap to enter main menu
Indicates when NAV infobar is available
- Tap to display NAV infobar
- Tap again to hide it
Connected mobile phone battery
status.
Mobile phone GSM reception fi eld
strength
Basic elements (for all playback sources)
Three infobar styles:
NAV infobar Playback infobar BT infobar
NOTE:
Press and hold the NAV button to fade in/out the infobars manually.
Touch the
icon to fade out the infobars manually.
NAV infobar is only available during active route guidance.
An incoming call or new playback information triggers the automatic
pop-up of the other infobar types at NAV screen. They will fade out after
ve seconds.
10
RADIO MODE
Display elements:
Red line marks current frequency
Frequency or station name
Traffi c announcement status
Traffi c announcements on carrier
LOC/DX status
Stereo reception indicator
Control elements:
Scroll left
Previous station
Tap to select center display content
Next station
Scroll right
100 kHz down
Drag to adjust frequency
100 kHz up
11
ZE
-
N C 3 15 2
RADIO MODE
RDS text allows a radio station to transmit
free-form textual information that can be
either static e.g. station slogans or in sync
with the programming such as the title
and artist of the currently playing song or
even short ads. Availability depends on
region, reception quality and carrier.
12
RADIO MODE
Select preset or save a preset. Press
and hold a center button to enter a new
frequency as preset.
To select a radioband tap on a
center button.
13
ZE
-
N C 3 15 2
RADIO MODE
NOTE:
This unit features an RDS tuner. RDS is a system which transmits data
on top of the FM radio signal. Availability and content of the RDS data
depend on the respective broadcast station and its signal strength. RDS
does, for example, transmit alternative frequencies, which allow for
frequency changes without user interaction. AM band doesn´t support
RDS functions.
You need to have the AF function activated in order to use the RDS
feature. However, the AF function is deactivated ex factory. We
recommend to activate it directly after mounting/installation of your device.
Lower bar options:
The selected item is highlighted in orange on the screen:
AF ON/OFF: When activated, AF function automatically switches to an
alternative frequency (AF) of your chosen station, in order to always offer
the best possible reception quality.
TA ON/OFF: When activated, the radio temporarily switches, for the duration
of the traffi c announcement, to tuner mode.
AS Searches for the six strongest stations and saves them as preset.
SCAN Intro-scan of all stations in reception range. You can hear each station for
a short moment. Lock to the one you like by pressing scan again.
REG ON/OFF: At certain daytimes some stations divide their program into
regional subprograms. The REG function prevents your receiver from
switching to an alternative frequency with different content.
LOC Touch LOC/DX to omit or allow reception of stations with weak signals.
/DX If LOC is activated it will exclusively tune to strong stations.
14
Display elements:
Source
Current folder/playlist
ID3 tag info
Progress bar
Album Art
PLAYBACK IPOD/USB/SD/DISC
Control elements:
Previous track
Play/Pause
Next track
Repeat
Shuffl e
Switch to playlist page
Playback page:
15
ZE
-
N C 3 15 2
PLAYBACK IPOD/USB/SD/DISC
Display elements:
iPod mode
Track/folder/playlist
Current folder
Control elements:
Previous track
Play/Pause
Next track
Repeat
Shuffl e
Cursor up
Cursor down
Switch to playback page
Switch to iPod audio mode
Switch to iPod video mode
Go to root directory
Search
Folder/playlist up
Playlist page iPod:
16
PLAYBACK IPOD/USB/SD/DISC
Display elements:
Track index
Track/folder
Current folder
Control elements:
Previous track
Play/Pause
Next track
Repeat track
Shuffl e
Cursor up
Cursor down
Switch to playback page
Go to root directory
Search
Folder up
Playlist page USB/SD/Disc:
17
ZE
-
N C 3 15 2
PLAYBACK IPOD/USB/SD/DISC
USB/SD/Disc modi search:
Tapping on
Search pops up an
numeric keyboard, allowing you to
enter track numbers. Numeric search
is unique for USB/SD/Disc modi.
Search function:
iPod search:
Tapping on
Search pops up an
alphabetic keyboard, allowing you
to enter an initial letter. Alphabetic
search is unique for iPod mode.
Tapping on
pops up the
keyboard option allowing you to
select your preferred keyboard
language.
18
PLAYBACK IPOD/USB/SD/DISC
Control elements:
Previous title/track/chapter
Play/Pause
Next title/track/chapter
To playlist/root menu of DVD
Full screen mode
DVD settings
Display elements:
Current temporal position in track
Total duration of track
Elements to control playback of video fi les:
19
ZE
-
N C 3 15 2
PLAYBACK IPOD/USB/SD/DISC
NOTE:
See www.zenec.com for:
Compatible fi le formats and their possible restrictions.
iPod/iPhone compatibility list.
PLAYBACK IPOD/USB/SD/DISC
USB/SD/Disc mode:
Make sure your mass storage device is FAT32 formatted.
Depending on directory structure and contents the total number of available
folders is limited.
Sorting and reaction time depends on speed and capacity of the mass
storage used, as well as on the amount of stored data.
Connected USB hard disks have to be formatted with FAT32 and are only
allowed to consume a maximum of 400mA (peak) current. Otherwise they
must be considered incompatible and can´t be used with the device.
Only iPod mode supports album art.
iPod mode:
Depending on the size of the search list, results may be delayed during first
search. That is due to the iPod, which takes a moment to setup and provide
the search index.
iPods/iPhones display, depending on content and sorting, an extended set of
information on the playlist page.
20
BLUETOOTH MODE
Bluetooth main menu:
Control Playback
A2DP On/Off (highlighted=ON)
Onscreen keypad
Call Log
Favourites
Audiostreaming (A2DP) toggle
Contacts
Bluetooth settings
A2DP (de-)activation:
Control elements:
Control elements:
Tap icon to select element.
21
ZE
-
N C 3 15 2
BLUETOOTH MODE
Display elements:
First incoming call
Second incoming call
Dialled number
Accept call, dial, hang up, switch between calls:
Control elements:
Keypad
Delete last digit
Pick up call / Switch to second call
Toggle to shift call between handsfree
and mobile phone (privacy mode)
Hang up active call / Back to fi rst call
Back to BT main menu
Caller II
Caller I
22
BLUETOOTH MODE
Pairing a mobile phone:
Tap on "Add" to trigger a search for BT devices.
2
Enter BT settings > Device
1
Control elements:
Add a mobile phone and input PIN
for pairing
Back to BT settings
Tap to select mobile phone
Browse list (up/down)
Choose your mobile phone from the list or retry searching. Press "Add".
3
23
ZE
-
N C 3 15 2
BLUETOOTH MODE
Upon request enter identical PIN code on your mobile and acknowledge.
You should now get a screen saying "Device successfully paired".
5
PIN code
Deletes the last digit
Acknowledge PIN code and continue
Enter PIN code and tap OK or retry
.
4
NOTE:
If you are trying to pair more than one mobile phone:
Switch off the "auto connect" function while pairing additional mobile
phones with the device.
Use different PIN code twins for each paired mobile phone.
24
BLUETOOTH MODE
Contacts - Manage phonebook:
 
No function, when keypad is active
Quit keypad
Display input
Tap to delete last character
Switch to next page of keypad
Search for an entry:
NOTE:
You may search for up to 15 leading characters.
Back to BT main menu
Tap a contact number to start a call
Search
Tap on star to save as favourite
Choose contact name from list
Select preferred keyboard language
Control elements:
25
ZE
-
N C 3 15 2
BLUETOOTH MODE
Go back to BT main menu
Go to contacts page
Tap to display outgoing call list
Tap to display incoming call list
Tap to display missed call list
Go to favourites page
Tap on contact name to call
Page up/down
Manage phonebook:
Control elements:
NOTE:
The synchronisation, the transferring, the sorting as well as the display
of the phone book entries depend on the mobile phone brand and model.
If the synchronisation doesn't work properly, disconnect the mobile phone
and repeat the pairing process.
If automatic phone book synchronisation does not work, consult the
manual of your mobile phone. Some mobile phones require explicit
activation of that function.
After entering the BT main menu press & hold either the Contacts or
Call-Log icon in order to force a resync of the entire phone book (if you
have experienced syncing problems).
26
BLUETOOTH MODE
Setup settings:
Back to BT main menu
Options
BT device settings
Microphone selection
Tap +/- to adjust microphone gain
Manage favourites:
Tap on contact name to call a
favourite
Delete favourite
Control elements:
NOTE:
Be aware that solely terminating the connection, or deleting a connected
mobile phone, does not affect the list of favorites. Favourites have to
be explicitly deleted one by one.
27
ZE
-
N C 3 15 2
BLUETOOTH MODE
NOTE:
If your mobile phone is compatible and still does not appear in the device
list, make sure Bluetooth is turned on and set to "visible for all devices".
Bluetooth connections usually work within a range of approx. 8 m.
Obstacles in the way may shorten the distance.
You can pair up to five mobile phones, and synchronise up to a thousand
phonebook contacts each.
In order to use the built-in handsfree function you need to pair your
mobile phone first.
It cannot be guaranteed, that all mobile phones can be paired and
that all functions will work.
For the "BT compatibility list" of tested and compatible mobile phones
as well as the latest software updates look out on www.zenec.com.
BLUETOOTH MODE
28
NAVIGATION MODE
Tap on "Find".
Choose your preferred destination
search method. Here, in our example,
choose "Find address".
Type in a city, street name,
house number and confirm
each step
by tapping
.
The program is now calculating the
desired route. Once route calculation
has completed just tap "GO!" to
enter active route guidance mode.
How to input a destination and start a route guidance:
29
ZE
-
N C 3 15 2
NAVIGATION MODE
NOTE:
For operation and detailed description of navigation features, please
refer to the separate navigation manual.
You may listen to any playback source in route guidance mode.
The navigation software automatically manages volume levels of
voice guidance.
If you change the volume level during voice guidance, the chosen volume
level gets stored for later route guidance.
Audio playback is, during voice guidance, capped to volume 10.
If the preset audio volume is below 10, it will be muted.
30
SYSTEM SETUP: MAIN / FIRST SETTINGS
Main setup screen:
Settings to attempt after mounting and initial startup:
Set OSD language: Go to Setup>General>Language
to choose your desired OSD
language. Animated picture visualises
your setting.
Set Reverse Camera: Go to Setup>General>Driver Assist
Needs to be enabled to use the
camera. Animated picture visualises
your setting.
Control elements:
Return to the previous menu.
Works with all four submenus.
See chapter Setup Video.
See chapter Setup Audio.
See chapter Setup General.
See chapter Setup Misc.
31
ZE
-
N C 3 15 2
SYSTEM
SETUP: IMPORT/EXPORT SYSTEM SETTINGS
Go to Setup>Misc>Help
SYSTEM
NOTE:
Make sure the USB flash drive has been FAT32 formatted.
Refrain from manually modifying the generated export file. Re-import
relies on proper file integrity.
After adding new functions, by means of a system update, they will
always be intialised with standard default values. That compensates for
lacking values from the import file content.
After a firmware update, check the update installation instructions for
notes on system settings import and take them into consideration.
1. Connect USB flash drive to device.
2. Tap "OK", at System Settings-Import
option, to launch import.
3. Restart device upon import completion.
Export system settings:
1. Format USB flash drive with FAT32.
2. Connect USB flash drive to device.
3. Tap "OK", at System Settings-Export
option, to launch file export.
Import system settings:
32
SYSTEM SETUP: VIDEO
Animated picture visualises TV shape
settings.
Animated picture visualises your setting
during adjusting TFT screen brightness.
Day-/Night TFT screen brightness is
controlled by GPS time signal.
Standby activation turns screen OFF.
Apart from that, the device operates in
a normal manner.
Tap on the screen to exit standby.
33
ZE
-
N C 3 15 2
NOTE:
NOTE:
Picture
TFT bright-
ness control
Brightness Day 0...20
Brightness Night 0...20
Name Descriptor Function Choice/Range
TV-Shape
Video display
setting
TV-Shape
Normal
Cinema
Standby TFT OFF
34
SYSTEM SETUP: AUDIO
Audio mixer:
Choose "Last" to adjust to last volume.
Choose "Set" to adjust to an arbitrary
value.
Level adjustments for sources:
Adjust volume relative to other sources.
Animated picture visualises fader and
balance settings.
EQ frequency adjustments
Adjust EQ bands.
Animated picture visualises
sub-out level.
If your vehicle is equipped with
an integrated OE Soundsystem,
activate parameter "OE Soundsystem"
in order to avoid audio distortion.
Tap "OK" at EQ to open equalizer page.
35
ZE
-
N C 3 15 2
NOTE:
Volume
Descriptor Function Choice/Range
Audio mixer
Start volume last value, set value
Set start volume 0...40
TA volume last value, set value
Set TA volume 0...40
NAV volume last value, set value
Set NAV volume 0...40
Level adjustment
of sources
Tuner rel. 0...14
CD/DVD rel. 0...14
USB/SD/iPod rel. 0...14
A/V In rel. 0...14
Sound
Level
assignment
Fader
front 9, center 0, rear -9
Balance
left -9, center 0, right 9
EQ
frequencies
Set bass frequency 50, 100, 200 Hz
Set mid frequency 0.5, 1, 2 kHz
Set treble frequency 5, 10, 15 kHz
Loudness
On, Off
Sub-Out
Sub-Out
settings
Level rel. -7...+7
Crossover 55, 80, 120 Hz
NOTE:
Speaker
Speaker system
settings
OE Soundsystem On, Off
Open Equalizer OK
36
SYSTEM SETUP: GENERAL
System time gets periodically updated
by GPS time stamp.
Animated picture visualises your driver
assist settings. Example: Reverse
Camera.
Reverse mute: Mute audio when
reverse gear is engaged.
Beep
Shown flag visualises the chosen
OSD language.
37
ZE
-
N C 3 15 2
NOTE:
NOTE:
Name Function Choice/Range
Main
Beep On, Off
Radio area Europe, USA, Latin (America)
Bluetooth On, Off
Volume Pop-Up On, Off
Antenna supply On, Off
NOTE:
Switch above mentioned antenna supply parameter to "Off", if your
vehicle does not deploy an active antenna.
Language OSD Set OSD language
Driver
assist
Parking assist Off, Rear view camera
Alt button Infobar, Standby
Reverse mute
On, Off
38
SYSTEM SETUP: MISC
You may export/import your system
settings to/from a USB flash drive.
A nice feature, to restore your device
settings after a firmware update, or a
complete power disconnection.
Tap "OK" to display corresponding
software version.
Activate password function to
secure device in case of temporary
disconnection from power supply (theft).
Use an arbitrary 4-digit code. To reset
the code enter "0000" instead.
Press "OK" to launch a software update.
For preparations and details, consult the
accompanying update installation
instructions BEFORE you run software
updates.
39
ZE
-
N C 3 15 2
NOTE:
NOTE:
Help
Calibrate TS OK starts touchscreen calibration
Load factory OK loads factory settings
System settings
Export settings to USB
System settings
Load settings from USB
NOTE:
Compare installed software versions with potentially newer versions on
www.zenec.com (see support and download area for updates).
Security
Password enable On, Off
Password
OK sets password
Update Update OK starts software update
Info
Show Info Software
Show Info
BT Software
Show Info
RDS
40
REMOTE CONTROL MAIN
1$
1#
1@
1!
1)
o
y
u
i
q
w
e
r
t
1*
1&
1^
1%
1(
2)
2!
2@
2#
2$
2%
2^
2&
2*
Remote Control Buttons
41
ZE
-
N C 3 15 2
1. POWER
Device ON/OFF
2. EJECT
Eject disc
3. MUTE
Mute/Un-mute audio output
4. SRC
Change sources
5. KEYPAD
Input track/chapter/title
6. VOL+
Increase volume
7. VOL-
Decrease volume
8. INFO
Show DVD info
9. GOTO
Open numeric onscreen keypad
10. STOP/BAND
Stop DVD/change radio band
11. SEL
Open EQ
12. ESC
Close menu/EQ
13. MENU
Open main menu
14. PIC
No function
15. REPEAT A B
Set start and end point at DVD
to repeat
16. OK
Play/Pause; Confirm
17. DIRECTION BUTTONS
Select item; move cursor
18. TITLE
Open DVD Title menu
19. ROOT
Open DVD main menu
20. REPEAT
Repeat track/chapter/title
21. SKIP NEXT
Jump to next track/preset/
chapter/title
22. SKIP PREVIOUS
Jump to previous track/preset/
chapter/title
23. FAST REVERSE
Fast reverse; 50kHz down at tuner
mode
24. FAST FORWARD
Fast forward, 50kHz up at tuner
mode
25. AUDIO
Change DVD audio language
26. ZOOM
Zoom in/out
27. ANGLE
Change DVD viewing angle
28. SUB-T
Change DVD subtitle
NOTE:
Some functions may not be available; depending on selected mode
and type of media.
REMOTE CONTROL MAIN
REMOTE CONTROL MAIN
42
REMOTE CONTROL M-ZONE
EPG
TV/RADIO
P P
DTV MENU
ROOT
MODE
SRCH
1$
1#
1@
1!
1)
o
y
u
i
q
w
e
r
t
1*
1&
1^
1%
1(
2)
2!
Remote Control Buttons
43
ZE
-
N C 3 15 2
1. MODE
Change source
2. KEYPAD
Input track/chapter/title
3. MUTE
Mute/un-mute audio output
4. GOTO
Open numeric onscreen keypad
5. TITLE
Open DVD Title menu
6. ROOT
Open DVD main menu
7. OK
Play/Pause; Confirm
8. DIRECTION BUTTONS
Select item; move cursor
9. SKIP PREVIOUS
Jump to previous track/preset/
chapter/title
10. SKIP NEXT
Jump to next track/preset/
chapter/title
11. STOP
Stop playback
12. PLAY/PAUSE
Play/pause playback
13. ZOOM
Zoom in/out
14. FAST REVERSE
Fast reverse
15. FAST FORWARD
Fast forward
16. SLOW
Slow motion playback
17. REPEAT
Repeat track/chapter/title
18. AUDIO
Change DVD audio language
19. SUB-T
Change DVD subtitle
20. ANGLE
Change DVD viewing angle
21. REPEAT A->B
Set start and end point at DVD
to repeat
NOTE:
Some functions may not be available; depending on selected mode
and type of media.
REMOTE CONTROL M-ZONE
REMOTE CONTROL M-ZONE
44
EXTERNAL PLAYBACK AND SOURCES
M-Zone
NOTE:
With deactivated M-Zone you will not see any signal on connected
M-Zone monitors (blackscreen).
The M-Zone volume cannot be adjusted on the device. Use the control
elements of the connected peripherals (i.e. roof monitor) instead, to adjust
the volume.
If the M-Zone and the front zone get both fed by one and the same
media source, the M-Zone stereo output will be muted.
The headunit does not memorize that the M-Zone has been activated
after shutting off. Therefore you have to reselect the M-Zone after
each re-start.
Control elements:
Direct access to main menu
Choose DVD
Choose DVB-T
Deactivate M-Zone
Control elements:
Direct access to DVB-T
Direct access to M-Zone
45
ZE
-
N C 3 15 2
EXTERNAL PLAYBACK AND SOURCES
DVB-T
NOTE:
For DVB-T reception you need to connect an external ZENEC DVB-T
receiver. For a perfect compatibility match check out the manual and the
compatibility list in advance.
Compatible DVB-T devices offer direct operation via touchscreen of the
headunit.
The headunit does not memorize that the DVB-T receiver has been
activated after shutting off. Therefore you have to reselect DVB-T after
each re-start.
Control elements:
Tap into the upper right corner to
return to the main menu
Control elements:
Direct access to DVB-T
46
GLOSSARY
A2DP Advanced Audio Distribution Profile, Bluetooth Audio
AC-Control Optical indication showing air condition status information
A/V In Audio-Video Input
AUX In Auxiliary Input, Audio only Input
CAN-Bus Controller Area Network-Bus; Automotive industrial standard
bus system
CAN/Stalk IF Interface to communicate with CAN-Bus
DVB-T Digital Video Broadcasting – Terrestrial; TV transmission standard
EQ Equalizer
FAT32 File allocation table 32-bit
GSM Global System for Mobile Communications, Mobile phone network
GUI Graphical User Interface
HMI Human Machine Interface (graphical part = GUI)
ID3-Tag Format to display additional info together with MP3 audio files
Media Link box Box to reroute some inputs from the back of the headunit to
easier accessible locations
M-Zone Rear seat entertainment area
OBC On Board Computer, Menu to control board computer
OE Original Equipment > OEM Original Equipment Manufacturer
OPS Optical Parking system (shows parking radar)
OSD On Screen Display
POI Navigation: Point of interest
Phantom pow. "In-line" antenna power supply; Power and antenna signals
use the same wire
TMC/TMC Pro Traffic Message Channel/Traffic Message Channel Professional
Pro with extended pay content
47
ZE
-
N C 3 15 2
TROUBLESHOOTING
Problem Cause Solution
GENERAL
Unit will not
power on.
Radio fuse blown. Install new fuse with correct rating.
Car battery fuse blown. Install new fuse with correct rating.
Illegal operation. Press the RESET button.
No/low audio output.
Improper audio output connection. Check wiring and correct.
Volume set too low. Increase volume level.
Speakers damaged. Replace speakers.
Only one channel is playing.
Check the balance and fader
adjustments.
Speaker wiring is in contact with
metal part of car.
Insulate all speaker wiring
connections or replace the speaker
cable.
Mute is activated. Turn off the Mute function.
Poor sound quality
or distortion.
Unauthorized disc is in use. Use original disc.
Speaker power rating not
compatible with unit.
Connect proper speakers.
Speaker is shorted. Check speaker connections.
TFT MONITOR
No image.
The parking brake is not engaged.
Stop vehicle in a safe place and
apply parking brake.
The "Monitor off"-function is
activated.
Touch the monitor to activate the
display.
Prolonged image
or improper height/
width ratio.
Improper aspect ratio setup. Use correct aspect ratio setting.
48
TUNER
Weak station searching.
Auto antenna not
properly connected.
Connect the auto antenna
cable properly.
REG function is activated. Turn REG function off.
The AF function is not activated. Activate the AF function.
MP3
The ID3 tags are shown
incorrectly.
Message is longer than LCD
can display or ID3 tag is not
compatible.
Use proper ID3 tag information.
DVD-PLAYER
Disc
does
not play
back.
[Bad Disc] Disc is warped or scratched. Use disc in good condition.
[Bad Disc] Disc is dirty or wet. Clean disc with soft cloth.
[Unknown
Disc]
Incompatible disc is used. Use compatible disc.
[Unknown
Disc]
Disc rating exceeds parental lock
rating limit.
Change parental lock settings
to lower restriction.
[Region
Error]
Disc region code is not
compatible with unit.
Use disc with proper region
code.
[Bad Disc] Disc is inserted upside down. Insert disc with label side up.
Cannot insert disc. Disc already inside unit.
Eject current disc and insert
new one.
49
ZE
-
N C 3 15 2
SPECIFICATIONS ZE-NC3152
GPS NAVIGATION SYSTEM
3D High-Definition navigation system
TMC and TMC Pro receiver
External GPS antenna
8 GB internal flash memory with map data for 43 Eastern and Western European countries and
Premium POI database
Graphical user interface and voice guidance in 28 different languages
2D or 3D map view with auto-zoom and display of 3D terrains and 3D landmarks
Eco and Smart Route Planning, Outlook address import, Real Junction View and Real Signpost
rendering etc.
Text to Speech function
PARROT BLUETOOTH HANDS-FREE MODULE
Synchronization of up to 1,000 contacts with max. 5 telephone numbers per contact
Alphabetical search function for contacts
Internal and external microphone
Future-proof upgradable Bluetooth firmware
MULTIMEDIA PLAYER
DVD loader
USB 2.0 port (via Media-Link box)
SD/SDHC card reader (up to 32 GB)
Made for iPod/Made for iPhone
Playback DVD loader: CD, CD-R/RW, MP3, WMA, DVD, DVD±R/RW, DVD-MP3, AVI, Xvid
Playback SD/USB: MP3, WMA, AVI, Xvid
GENERAL FEATURES
Intuitive, user friendly HMI in 20 different languages
6.2“/15.7 cm 16:9 HD TFT-LCD display with 800 x 480 pixels resolution and touchscreen control
RDS dual tuner with 30 preset stations (18 FM/12 AM)
Multi zone function
4 x 50 watts class-D amplifier
2 x IR-remote control
A/V-CONNECTIONS
4.2-CH preamp line outputs
2-CH preamp line outputs without volume adjustment
2 x composite video outputs (NTSC)
1 x A/V-input
1 x video input for rear view camera with switching function
Connectivity for compatible external DVB-T or DAB+ receivers
BRAND/VEHICLE SPECIFIC FEATURES
Steering wheel remote control integration via CAN
Driver information system (FIS) integration via CAN (Audio information and Nav turn key
information)*
Soundsystem integration, incl. BOSE Soundsystem
Red key illumination
* Functionality only provided if feature specific CAN data is present.
ƽ NOTE: SPECIFICATIONS AND DESIGNS OF THIS MODEL ARE NECESSARILY SUBJECT
TO CHANGE WITHOUT NOTICE.
50
INHALTSVERZEICHNIS
SICHERHEITSHINWEISE .................................................................................... 51
TASTEN DES BEDIENTEILS .........................................................................52-53
BEDIENUNG MULTIFUNKTIONSLENKRAD ................................................54-55
GRUNDLEGENDE BEDIENUNG ...................................................................56-57
RADIO MODUS ...............................................................................................58-61
WIEDERGABE ................................................................................................62-67
BLUETOOTH MODUS .................................................................................... 68-75
NAVIGATIONS MODUS ..................................................................................76-77
SYSTEM SETUP ............................................................................................. 78-87
HAUPTFERNBEDIENUNG .............................................................................88-89
M-ZONE FERNBEDIENUNG .......................................................................... 90-91
EXTERNE WIEDERGABE UND QUELLEN ..................................................92-93
GLOSSAR ............................................................................................................ 94
FEHLERSUCHE ..............................................................................................95-96
SPEZIFIKATIONEN ............................................................................................. 97
GARANTIE .....................................................................................................98-99
EC KONFORMITÄTSERKLÄRUNG ................................................................. 102
ƽ Die Bedienungsanleitung für die Navigationssoftware befindet sich in einem
separaten Handbuch.
51
ZE
-
N C 3 15 2
SICHERHEITSHINWEISE
1. Lesen Sie die Anleitung vollständig durch.
2. Bewahren Sie die Anleitung sorgfältig auf. Sie sollte jedem Benutzer dieses Gerätes frei
zugänglich sein.
3. Beachten Sie sämtliche Warnungen und befolgen Sie die Anweisungen, um Probleme zu vermeiden.
4. Dieses Gerät ist nur für den Betrieb an einem Bordnetz mit +12V DC und Minus gegen
Masse geeignet.
5. Montieren und bedienen Sie das Gerät nur so, wie es in der Bedienungsanleitung beschrieben wird.
Alles andere kann zum Erlöschen Ihres Garantieanspruches führen.
6. Zerlegen oder modifizieren Sie das Gerät nicht. Ihr Garantieanspruch erlischt dadurch. Versuchen
Sie auch nicht das Gerät selbst zu reparieren oder zu warten, sondern wenden Sie sich an einen
autorisierten ZENEC-Fachhändler.
7. Benutzen Sie nur das Originalzubehör, um das Gerät zu installieren und zu betreiben, da an-
sonsten eine Beschädigung des Gerätes riskiert wird. Befestigen Sie das Gerät gemäß der
Installationsanleitung, unter Verwendung des mitgelieferten Montagezubehörs. Die bei Unfällen
auftretenden Beschleunigungskräfte sind teilweise enorm. Unsachgemäß montierte Geräte stellen
bei Unfällen ein großes Risiko für den Fahrer und die Insassen des Fahrzeuges dar.
8. Schützen Sie das Gerät vor Wasser oder anderen Flüssigkeiten, die in das Innere des Gerätes
eindringen können. Sonst könnte ein Kurzschluss mit Brandfolge daraus resultieren.
9. Zur Vermeidung eines Kurzschlusses achten Sie darauf, daß keine metallischen Gegenstände in
das Gerät gelangen.
10. Bevor Sie eine defekte Sicherung austauschen, sollten Sie erst überprüfen was der Grund für
den Kurzschluss war. Achten Sie dabei besonders auf die Kabel der Spannungsversorgung!
Wenn der Kurzschluss nicht durch einen Fehler in der Spannungsversorgung verursacht wurde,
müssen Sie die defekte Sicherung gegen ein neues Exemplar mit identischen Werten austauschen.
Sollte der Kurzschluss immer noch vorhanden sein, wenden Sie sich bitte an einen autorisierten
ZENEC-Fachhändler.
11. Lesen Sie die Bedienungsanleitung eines fremden Gerätes und versichern Sie sich, daß es
kompatibel ist, bevor Sie es anschliessen. Schliessen Sie keinesfalls inkompatible Geräte an.
12. Achten Sie darauf, dass bei ausgeschaltetem Motor die Batterie des Fahrzeuges nicht entladen wird.
Da es sich bei dem Gerät um einen Verbraucher handelt und die Batterie nur bei laufendem Motor
aufgeladen wird, kann es passieren, dass die Batterie tief entladen wird und sich das Fahrzeug nicht
mehr starten lässt.
13. Gemäß den in den verschiedenen Ländern der EU geltenden Verkehrsvorschriften, darf ein Monitor,
der in Sichtweite des Fahrers montiert ist, während der Fahrt, ausser zu Navigationszwecken, nicht
mit bewegten Bildern oder Filmen betrieben werden, da er den Fahrer vom Verkehrsgeschehen
ablenkt. Beachten Sie unbedingt die geltenden Vorschriften in Ihrem Land, da ansonsten bei einem
Unfall Regressansprüche von der Kfz-Versicherung geltend gemacht werden können. Achten Sie
zusätzlich darauf, dass die Lautstärke in Ihrem Fahrzeug nur so hoch ist, dass Sie Außengeräusche,
wie z.B. eine Polizeisirene, noch klar wahrnehmen können.
14. Setzen Sie das Gerät keinen harten Stößen aus. Eine mechanische und elektronische Beschädigung
des Gerätes könnte daraus resultieren.
15. Wenn Sie Fragen oder Probleme bei der Installation haben, wenden Sie sich bitte an einen
ZENEC-Händler oder den jeweiligen Landesvertrieb.
16. Das Gerät verwendet einen Laser Klasse 1. Benutzen Sie das Gerät ausschliesslich wie in der
Anleitung beschrieben, um eine Gefährdung durch koherentes Licht auszuschliessen. Sie sollten das
Gerät weder Öffnen noch selbst reparieren. Reparaturen sollten ausschliesslich von qualifizertem
Servicepersonal durchgeführt werden.
80
SYSTEM SETUP: VIDEO
Passen Sie hier das dargestellte
Bildschirmseitenverhältnis dem
Seitenverhältnis der Videodatei an.
Eine Bildschirmanimation visualisiert
Ihre TFT Helligkeitseinstellungen.
Die Umschaltung der Tag- und Nacht
Helligkeiten erfolgt automatisch nach
Auswertung des GPS Zeitstempels.
Standby-Aktivierung schaltet den
Bildschirm dunkel. Davon abgesehen,
läuft das Gerät normal weiter.
Ein Tippen auf den Bildschirm schaltet
diesen wieder hell.
80


Need help? Post your question in this forum.

Forumrules
1

Forum

zenec-ze-nc3152---audi-tt
  • My screen is stuck on the ‘Zenec’ logo. I have reset, turned on and off, switched my engine off and for 3 days now it still is not working Submitted on 16-2-2020 at 18:31

    Reply Report abuse
    • My neighbor's did the same thing yesterday. Did you ever solve the problem? Thx. Answered on 7-6-2020 at 05:13

      Vote up (4) Report abuse
    • Hi!

      I have the same problem with my Zenec unit. Screen is just stuck on "ZENEC" and radio is on in the background. None of the buttons do anything. How did you resolve the problem? Answered on 10-1-2023 at 21:24

      Vote up (9) Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zenec ZE-NC3152 - AUDI TT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zenec ZE-NC3152 - AUDI TT in the language / languages: English, German as an attachment in your email.

The manual is 4,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zenec ZE-NC3152 - AUDI TT

Zenec ZE-NC3152 - AUDI TT User Manual - English - 89 pages

Zenec ZE-NC3152 - AUDI TT Additional guide - English - 1 pages

Zenec ZE-NC3152 - AUDI TT Installation Guide - English - 6 pages

Zenec ZE-NC3152 - AUDI TT User Manual - German - 98 pages

Zenec ZE-NC3152 - AUDI TT Additional guide - German - 1 pages

Zenec ZE-NC3152 - AUDI TT Installation Guide - German - 6 pages

Zenec ZE-NC3152 - AUDI TT User Manual - Dutch - 96 pages

Zenec ZE-NC3152 - AUDI TT User Manual - Dutch - 56 pages

Zenec ZE-NC3152 - AUDI TT User Manual - French - 95 pages

Zenec ZE-NC3152 - AUDI TT User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info