Manual Zelmer Tiny VC1400.0 SK (page 58 of 62) (English, Polish)

539694

Zoom out

Zoom in

1/62

64 VC1400-001_v02

Special accessories

The following special accessories may be purchased in retail

outlets:

Parquet brush “BNB” (22)

Is used to clean and polish hard, scratch sensitive surfaces

such as wooden oors, oor panels, parquet, marble, tiles,

etc.

Delicate and soft natural bristles ensure maximum vacuum

effectiveness and protects against scratching the cleaned

surface.

Zelmer turbobrush (23)

May be used with all types of ZELMER vacuum cleaners.

Is used for an effective vacuuming of carpets and tted

carpets. While using the turbobrush follow the instruction

manual.

The use of the turbobrush decidedly increases the

effectiveness of removing brous dirt such as: animal hair,

hair, threads etc. It is practically useful in households with

pets (cats, dogs), where removing the animal hair from the

carpets and oorings is very onerous.

After-work procedures, cleaning and

maintenance

Press the on/off button to stop the vacuum cleaner.

Remove the plug of the cord from the socket.

Wind the cord by pressing the cord winder button (8).

Hold the cord when doing it to avoid tangling the cord up or

letting the plug hit the vacuum cleaner.

Disconnect the telescopic suction pipe from the nozzle or

brush.

Disconnect the suction tube from the hose. In order

to remove the telescopic tube from the hose handle,

simultaneously press the lock A and pull the tube in the

direction indicated by the arrow.

Turn the end of the suction hose counter-clockwise, and

remove the end of the hose from the inlet of the vacuum

cleaner.

The vacuum cleaner may be store in a horizontal

position. In order to do this place the hook of the nozzle

brush into the fastening of the nozzle brush situated at the

back of the vacuum cleaner, near the entrance of the power

cord. The hose may stay attached to the vacuum cleaner as

long as it is not bent too much during storage.

If necessary, clean the casing and the chamber of the

vacuum cleaner with a damp cloth (it may be damped in

dishwashing liquid), dry it off, and wipe it dry.

Donotuseanyscrubbingagentsorsolvents.

Place the new/rinsed HEPA H12 basic lter (14) in the

previously determined spot in the dust container.

Situate the protective casing of the HEPA H12 basic lter

in the chamber of the container, in the previously determined

spot. Pay attention that the protrusions situated on the ange

of the container are inserted in the sockets of the body of the

container.

Turn the protective casing of the HEPA H12 basic lter

in the direction given on the symbol „ ” (it is situated along

with an arrow on the protective casing of the HEPA H12 basic

lter).

Place the cover of the CYKLON dust container on the

container in such a way that the fastening situated in the

front part of the cover is inserted into the projection of the

container. Press the back part of the cover in such a way that

the fastenings are shut tight on the body of the container.

Situate the CYKLON dust container with the installed

HEPA H12 basic lter (14) in the chamber of the vacuum

cleaner. Close the upper cover of the vacuum cleaner by

pressing it, until you hear a characteristic “click.”

 WeadviseyoutoreplacetheHEPAH12basic

lter (14) with a new one every6 months of

use.

 Always replace a damaged HEPA H12 basic

lterwithabrandnew,originalone.

OUTLET MICROFILTER

In order to replace the outlet microlter (13) press the

blocking mechanism on the cover of the outlet lter, and then

remove the cover of outlet lter out of the vacuum cleaner.

Remove the outlet lter from the cover.

If the outlet microlter (13) is dirty, you may replace it with

a new one, clean it or rinse it with running water. Before

reinstalling the lter, make sure it is dry.

 Forsafetyreasons,itisunacceptabletoinstall

awetordamagedoutletmicrolter.

Situate the new/rinsed lter carefully onto the

4 fastenings of the outlet lter cover with the foam sides

towards themselves.

Place the lter cover in such a way that the two

protrusions situated in the lower part of the cover are

inserted into the holes in the body of the vacuum cleaner,

and then press the lter cover to snap the fastening in the

body shut. A characteristic “click” signalizes the lter cover

has been properly installed.

 Always replace a damaged microlter with

abrandnew,originalone.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Tiny VC1400.0 SK in the language / languages: English, Polish as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer Tiny VC1400.0 SK Manual

Product: