Manual Zelmer Nerro 13Z015 (page 61 of 64) (English, Polish)

538896

Zoom out

Zoom in

1/64

61GW13-022_v01

8.14. When the knob indicator (C) stops ashing and starts being

illuminated continuously, the coffee will come out of the machine.

8.15. The process of brewing will be automatically nished after attaining

the quantity of coffee set previously. Two signals will sound and the

knob indicator (C) will glow continuously.

8.16. Take off the lter holder by turning it left (Fig. 5), then throw away

the used bag or coffee grounds (Fig. 6). Clean the lter with water

(Fig. 7).

9.8. Pour ground coffee with the use of the measuring/tamping spoon

(13) or put the coffee in espresso bags into the container of the lter

holder (6).

9.9. Remove the exceed of coffee from the edge of the lter and tamp

coffee with the use of the tamping device fastened to the machine (5)

or the at end of the measuring/tamping spoon (13) (Fig. 4).

9.10. Put the lter holder (6) into the brew head (4), turning it rmly right

(Fig. 3).

9.11. Put a cup or cups on the drip tray grid (7), directly under the container

of the lter holder (6).

9.12. Turn the knob of the machine (B) in such a way that the manual

brewing of coffee indicator M (H) on the control panel will be

illuminated.

9.13. Press the knob of the espresso machine (B). The signal will sound.

If the espresso machine does not attain appropriate temperature for

use, the knob indicator (C) will start ashing to inform you that the

espresso machine is in the course of warming up.

9.14. When the knob indicator (C) stops ashing and starts being

illuminated continuously, the coffee will come out of the machine.

9.15. The process of brewing will be automatically nished after attaining

the quantity of coffee set previously. Two signals will sound and the

knob indicator (C) will glow continuously.

9.16. Take off the lter holder by turning it left (Fig. 5), then throw away the

used bag or coffee grounds (Fig. 6). Clean the lter with water (Fig. 7).

ATTENTION! If there is too small amount of water in the tank (1) during

the process of coffee brewing, the espresso machine will stop working.

The (N) indicator on the control panel will start ashing and the

repeating signal informing about the necessity to rell the tank with

water will sound. Open the cover of the water tank (1) and pour water.

Just after relling tank the sound signal will stop and the espresso

machine will automatically nish the coffee brewing process.

ATTENTION! You can stop the coffee brewing process at any time.

In order to do so you need to press the Power On/Off (A) button.

ATTENTION! During the process of coffee brewing do not set steam

release knob (12) to the position, because boiling water can

uncontrollably leak disturbing the process of coffee pouring at the

same time. The steam release knob (12) may be only used during

steam function.

10. Preparing steam (milk foaming)

For the process of milk foaming the steam function is used. The steam has

two tasks: it warms up and at the same time mixes milk with the air giving

it delicate, velvety appearance. Just like in coffee brewing process the best

effects in milk foaming you can get gaining experience in this eld.

Hint: Remember that coffee is the basis of every coffee drink and milk is

only addition.

ATTENTION! It is advisable rst to foam milk and then to prepare

coffee.

The steam function may be also used to warm up drinks.

10.1. Prepare beforehand espresso in accordance with the point 8 or 9.

10.2. Determine the amount of necessary milk based on the number of

cups or the size of a milk jug.

Hint: ● Remember that the milk volume rises during the process

of its foaming.

Pour cold milk into the stainless steel jug up to 1/3 to 1/2 of its ●

volume.

Hint: ● Keep the stainless steel milk jug in a fridge in such a way

that milk is chilled all the time. Remember not to rinse the jug

with hot water before its use.

10.3. Turn the knob of the espresso machine (B) in such a way that the

steam indicator (I) on the control panel will be illuminated. The

knob indicator (C) will immediately start ashing to inform you that

the espresso machine is in the course of warming up.

10.4. When the knob indicator (C) stops ashing and starts being

illuminated continuously, it means that the espresso machine is

ready for foam mode (that it has attained appropriate temperature).

10.5. Rinse the steam wand (10) putting under it different container then

a milk jug acting in accordance with point 6.2.4. The steam wand

was initially rinsed.

10.6. Then put the steam wand into a milk jug in such a way (Fig. 8),

that the wand is approx. 1/2 cm below the milk surface. Activate the

steam release by setting the steam release knob (12) again to the

position, that is turn it counterclockwise in such a way that the

symbol coincides with the mark on the casing of the espresso

machine.

Fig. 4 Fig. 5

Fig. 6 Fig. 7

ATTENTION! If there is too small amount of water in the tank (1)

during the process of coffee brewing, the espresso machine will stop

working. The (N) indicator on the control panel will start ashing

and the repeating signal informing about the necessity to rell the

tank with water will sound. Open the cover of the water tank (1) and

pour water. Just after relling tank the sound signal will stop and

the espresso machine will automatically nish the coffee brewing

process.

ATTENTION! You can stop the coffee brewing process at any time.

In order to do so you need to press the Power On/Off (A) button.

ATTENTION! During the process of coffee brewing do not set steam

release knob (12) to the position, because boiling water can

uncontrollably leak disturbing the process of coffee pouring at the

same time. The steam release knob (12) may be only used during

steam function.

9. Preparing espresso using function of manual

brewing of coﬀee

Thanks to this function a user has a possibility to make the size of coffee

that is the user’s liking.

9.1. Turn the machine off at the power outlet and unplug the power cord.

9.2. Fill the tank with water (1) in accordance with the point 4.

9.3. Connect the device to the power grid by putting the power plug into

a socket. The espresso machine will turn on. The signal will sound

the knob indicator (C) will ash 5 times. Then the knob indicator (C)

will go out.

9.4. Press the Power On/Off (A) button; the signal will sound.

9.5. The knob indicator (C) will start ashing to inform you that the

machine is in the course of warming up.

9.6. When the knob indicator (C) will stop ashing, the signal will sound.

If the knob indicator (C) will start being illuminated continuously,

the espresso machine is ready for use (attaining appropriate

temperature).

9.7. Choose the mode of coffee in espresso bags or the mode of ground

coffee and the temperature level (standard or hot) with the use of

(L) button – see point 7.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Nerro 13Z015 in the language / languages: English, Polish as an attachment in your email.

The manual is 3,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer Nerro 13Z015 Manual

Product: