539666

Zelmer Eco Power VC3100.0 SK Manual

63
Zoom out
Zoom in
Previous page
1/66
Next page
67
VC3100-001_v01
5
Carefully insert a new / rinsed lter to previously occupied
space.
6
Put the lter cover so that two tips located at the right
side of the cover should hit the holes in the body of the
vacuum cleaner, press the lter cover so the hook snapped
in the body. Characteristic “click” sound informs, that the lter
cover has been properly installed.
Donot use the vacuumcleaner withno inlet
andoutletltersmountedinthedevice.
Damagedinletandoutletltersmustbealways
replacedwithnew,factoryoriginallters.
THE CONE OF “CYCLONE” DUST CONTAINER
It is necessary to clean periodically the “CYCLONE” dust
container cone.
1
Disassembly “CYCLONE” dust container according to
point (C).
2
Press the button located on “CYCLONE” dust container
and open the bottom of the container. If “CYCLONE dust
container is full, empty it according to the point (C).
3
Turn the cone left, so the two tips located on the ange of
the cone were put out from the slots of the container. Put out
the cone.
4
If the “CYCLONE” dust container cone (17) is dirty, you
can rinse it with running water. Do not forget to dry above
mentioned cone before re-installation.
5
Insert the rinsed cone of “CYCLONE” dust container into
the container slot so the tip located on the ange of the cone
was in the slot of container’s body. Turn right the cone so that
the two tips located on the ange of the cone were blocked in
the slots of the container.
6
Snap the bottom of “CYCLONE” dust container. Please
pay attention to the proper positioning of seal found on the
bottom of the container.
7
Insert “CYCLONE” dust container to vacuum cleaner
chamber. The characteristic “click” indicates that the
container has been correctly mounted.
End of operation, cleaning and
maintenance
1
Switch off vacuum cleaner pressing On/Off switch (4).
2
Put the connection cable plug out the wall outlet.
3
Wind the cable by pressing retractor button (6).
Performing this action, hold the power cable to avoid any
tangles and shocking the vacuum cleaner body with the
plug.
4
Disconnect telescopic suction tube and a sucker or
a brush sweeper.
5
Disconnect telescopic suction tube and a hose.
6
Press the two side buttons located at the hose end, then
remove the hose end from vacuum cleaner inlet hole.
F
G
it or rinse with running water. Do not forget to dry above
mentioned lter before re-installation.
The main function of the foam inlet lter (15) is to protect
HEPA inlet lter (14) against excessive dirt.
Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedfoaminletlter(15).
Clean the pleats of HEPA inlet lter
●
(14), in case of lter
damage it should be absolutely replaced with a new
lter. If HEPA inlet lter (14) is dirty, you can replaced
it with a new lter, you can clean it or rinse with running
water. Do not forget to dry above mentioned lter before
re-installation.
Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedinletlterHEPA(14).
Insert a new/rinsed HEPA inlet foam lter
●
(15) into
previously occupied space.
3
Insert a new/rinsed HEPA inlet lter (14) to the dust
container into previously occupied space.
4
Insert “CYCLONE” dust container with mounted HEPA
inlet lter (14) to vacuum cleaner chamber. The characteristic
“click” indicates that container has been correctly mounted.
ItisrecommendedtoreplaceHEPAinletlter
(14)withanewoneevery6monthsofuse.
Do not vacuum withoutHEPA inlet lter (14)
installed in “CYCLONE” dust container. Lack
ofHEPAinletlter(14)shallpreventinsertion
of “CYCLONE” dustcontainer tothe vacuum
cleaner.
“MICROFILTER” OUTLET FILTER AND OUTLET
FOAM FILTER
1
In order to replace “Microlter” outlet lter (12) press the
hook located in the lter cover and pull out the lter cover
from vacuum cleaner.
2
Pull out the “Microlter” outlet lter (12).
If the “Microlter” outlet lter (12) is dirty, you can replace
it with a new lter, you can clean it or rinse with running
water. Do not forget to dry above mentioned lter before
re-installation.
Forsafetyreasonsitisunacceptabletoinstall
the moist or defective “Microlter” outlet
lter(12).
3
Carefully insert a new / rinsed lter to previously occupied
space.
4
Pull out the foam outlet lter from lter cover (1).
If the outlet foam lter (13) is dirty, you can replace it with
a new lter, you can clean it or rinse with running water. Do
not forget to dry above mentioned lter before re-installation.
Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedoutletfoamlter(13).
E
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer Eco Power VC3100.0 SK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Eco Power VC3100.0 SK in the language / languages: English, Polish as an attachment in your email.

The manual is 4,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info