Manual Zelmer Aquawelt 919.0 SP (page 61 of 66) (English, Polish)

539648

Zoom out

Zoom in

1/66

agent recommended by ZELMER S.A. in the amount and

manner indicated on the label.

„G 478 Entschäumer D” manufactured by the company –

BUZIL, Germany.

Prepare the vacuum cleaner for operation according

●

to section B.

ATTENTION! Use only the large or small atomizing

nozzle for wet vacuum cleaning.

The vacuum cleaner will by default begin operation at the

●

medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this

function is only available in vacuum cleaners type 919.0)

by pressing the power adjustment buttons +/- (8).

Press the pump switch (6).

ATTENTION! The pump may only be switched on when

the cleaning liquid container is lled with the solution

of cleaning liquid and water. The lack of cleaning liquid

manifests in a loud operation of the pump.

If the nozzle does not atomize water although the pump is

switched on, check if the following items are correctly installed:

the cleaning liquid container (press the container), the fastening

of the stub pipe in the valve in the base of the vacuum cleaner

or the fastening of the hose end in the atomizing nozzle, check

if the atomizing nozzle is not clogged.

Press the button adjusting the inow of water to the

nozzle on the hose handle.

If you press the button in a pulsating manner, the water shall

temporarily ow in a slower manner to the nozzle, if you

press and slide the button backwards, the water shall be

continuously supplied to the nozzle.

The handle is also equipped with a slider to adjust the suction

power. Do not uncover this opening while picking up water or

using the wet cleaning function.

ATTENTION! Do not spray the cleaning liquid in one

place on the carpet for too long in order not to soak

the carpet.

After cleaning one part of the carpet stop the spraying

●

process and dry the carpet by sliding the nozzle back and

forth. Repeat until the whole surface of the carpet is dried.

After ending the spraying process switch off the pump

●

and press the button adjusting the water inow to the

nozzle for a moment to “release the pressure”.

ATTENTION! The vacuum cleaner is equipped with a oat

which will automatically block the suction if the foam lter

II (32) is heavily dirty or the liquid exceeds the maximum

level. It is manifested by a pulsing limitation of the motor

power and the lighting up of the clogged air inlet indicator

(11) (type 919.0). In such a case switch off the vacuum

cleaner by pressing the on/off button (7), unplug the

appliance, clean the lter and empty the container.

In case of dirt which is difcult to remove moisten the surface

with the washing agent recommended by ZELMER S.A. until

foam is formed. Leave for some time and vacuum with the

vacuum cleaner.

ATTENTION! Make sure the carpet is not soaked.

It may lead to a permanent deformation of the carpet

(folding).

PICKING UP WATER

If you want to use the vacuum cleaner to vacuum liquid in

the container, the vacuum cleaner should be prepared as in

the case of vacuum cleaning with the use of the water lter

module except that:

1. The container should be empty (without water).

2. You are to use atomizing nozzles (large or small), large

atomizing nozzle with the gathering attachment or the

nozzle for picking up water.

ATTENTION! Do not operate the vacuum cleaner with

a full container! Do not vacuum large amounts of liquid

at a time (e.g. with the hose immersed into water).

If the water exceeds the maximum level during vacuuming,

the oat will automatically block the suction. The maximum

capacity of the container is about 5 l. In such a case proceed

in the manner described above in the part concerning the

blocking of suction caused by a dirty foam lter (pulsating

motor speed).

END OF OPERATION CLEANING AND MAINTENANCE

Switch off the vacuum cleaner by pressing the on/off

●

button (7) and unplug the appliance.

Wind the cord by pressing the cord rewind button

●

(10).

While doing this hold the cord to make sure it is not

tangled and the plug does not hit the vacuum cleaner

housing.

Turn the end of the hose until the tops of the marks

●

on the end of the hose end and on the vacuum cleaner

housing are in the same position and pull the hose out

of the opening.

Remove the stub pipe of the hose by pressing the red

●

button on the valve and pull the stub pipe.

Disconnect the telescopic tube from the hose and the

●

nozzle or brush.

Pour the dirty water out of the container.

●

It is recommended to wash the container, lters

●

(disassembly below) and partition thoroughly after each

use – changing water several times.

After using the wet cleaning function thoroughly wash

●

all attachments used in this process (hose, tubes,

accessories).

ATTENTION! If you do not clean the above-mentioned

parts or clean them insufciently it may lead to the loss

of the ltration capabilities of the inserts and foam and

cause the formation of bacteria and mites.

Dry all the cleaned parts thoroughly before reassembly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Aquawelt 919.0 SP in the language / languages: English, Polish as an attachment in your email.

The manual is 5,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer Aquawelt 919.0 SP Manual

Product: