Manual Zelmer 986 (page 73 of 74) (English, Polish)

538959

Zoom out

Zoom in

1/74

VIII. Pusher (from the mincing unit)

IX. Screen – 2 pieces

No. 1 – smaller openings

No. 2 – larger openings

X. Large sealing ring for the body (3)

XI. Small sealing ring for the worm (2)

XII. Hook

NOTE: Use only the pusher to push fruits (VIII).

Preparing for operation and operation

Make sure the sealing rings

●

(X) and (XI) are installed

on the body (III) and worm (II). If not, please install the

sealing rings in the openings of these elements (the body

and the worm).

Insert the screen

●

(IX) into the body (III) and push until

stop.

In order to remove the sieve (IX) out of the body (III), it

is helpful to use the hook (XII). Put the shorter end of

the hook (XII) into the hole of the sieve (IX), and pull

the sieve (IX) outside.

Insert the worm

●

(II) into the squeezer chamber (I) and

insert the body with the screen onto the worm paying

attention that the sieve is placed downwards, and the

positioning opening ts the protrusion of the squeezer

chamber.

Screw the nut

●

(IV) onto the squeezer chamber (I).

Screw the adjustment screw

●

(VI) into the body (III) and

insert the juice channel (V) until it snaps shut on the body

(III) and you hear a click.

Insert the assembled squeezer onto the motor,

●

proceeding in the same way as in the description of the

mincing chamber.

Insert the bowl

●

(VII) and the pusher (VIII) – from the

mincing unit onto the feeding tube.

Put some appropriate vessels for juice and pulp under

●

the juice channel outlet (V) and adjusting screw (VI).

Plug in the appliance.

●

Turn on the appliance by pressing the

●

„I” button and

next insert the fruits pushing them with the pusher.

In order for the juice squeezing process to run properly

do not screw the adjustment screw too deeply in the initial

operation phase. After assessing the amount of juice in

the processed fruits, adjust the screw in order to obtain an

adequate effectiveness and to avoid clogging the appliance.

Observe the pulp dryness during squeezing. If they

●

are too dry, unscrew the adjusting screw (VI), to avoid

clogging the appliance.

The screw adjustment depends on the type of processed

fruits, in case of juicy and ripe fruits adjust the screw

deeper, and for fruits that are not as juicy, the level of screw

adjustment should be lower.

If the screw adjustment does not provide an adequate

squeezing effectiveness, you can process the processed

fruits once again.

The clogging of the chamber outlet (in the adjustment screw

(III)) with juicy processed fruits can cause the juice to contact

the motor.

Unplug the appliance if the chamber outlet becomes

clogged. Pay special attention during the juice squeezing

process, make sure the screen openings are not clogged.

Dismantle the juicer from the motor (as in the case of the

mincing chamber), dismantle the squeezer, clean (wash)

the squeezer elements. Use the included brush to clean the

appliance, especially the screen.

Quern grinder (Fig. 10)

I. Nut

II. Quern regulator

III. Body with handle

IV. Internal quern

V. External quern

VI. Worm

VII. Grinder chamber

VIII. Pan

IX. The groove of the body has to hit the protrusion of the

grind chamber

Device description

Presented device can be used to grinding such products as:

corns, oily seeds and the dry comestibles

The quern grinder enables grinding of such products as:

wheat, oat, rice, granular coffee, all-spice, charlock, walnuts,

hazel-nuts dried mushrooms, almonds, soya. linseed,

buckwheat groats, peeled sunower seeds etc.

IMPORTANT: Don`t grind the oily products by the

minimal granulation set up. Grinding device can be

glued or blocked.

IMPORTANT: Device is not dedicated for grinding the

very hard products as f. e. dried pea, maize, popcorn.

The installation of the grinder on the device

When the grinder chamber is turned right through the angle

of 45, put the assembled grinder on the drive by putting the

protrusions of grinder chamber (VII) on the recesses of the

drive, and then, turn left to the position in which you will hear

“clicking” of the blocking. It means that the grinder has been

assembled correctly.

Usage and regulation of the grinder

Before the rst use, wash (see “CLEANING”) and dry

a disassembled grinder, and then grind around 50 grams of

product (f. e. corns) - set-up the grinding option of the device

with the medium comminute. The grinded product is not t to

use cause it` s polluted and its necessary throw it away.

IMPORTANT: Maximal time of uninterrupted work is

around 15 minutes.

This condition is connected with maximal work time of

machine, for which it should be done the 45 minutes of

pause after 15 minutes of operation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 986 in the language / languages: English, Polish as an attachment in your email.

The manual is 2,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer 986 Manual

Product: