538860

Zelmer 491 Symbio Manual

51
Zoom out
Zoom in
Previous page
1/54
Next page
55491-007_v01
inside the food processor container in one position only, so
that the protrusion of the permanent guard is locked inside
the handle of the food processor container.
4
Insert the lid of the food processor into the fasteners of
the container (take care that the lid is fastened with all the
fasteners).
5
Lock the lid.
6
Insert the blender drive (assembling of the drive is
possible only when the container lid is closed). Then lock it.
7
Set the desired gear using the speed control knob.
8
Insert processed products into the lid chute.
9
Hold the pusher to the chute, so that it does not press
the product before start – up of the appliance (push the next
portions of products when the blender drive is in operation /
the disc is rotating).
10
Connect the plug into the mains supply outlet. Then start –
up the appliance pressing the switch (2) of the blender drive.
After nishing operating the food processor (Fig. H)
1
Release the button (2) (or TURBO in case of using this
gear).
2
Remove the plug of the supply cord from the mains
supply outlet.
3
Unlock and remove the blender drive (after the appliance
stops completely).
4
Remove the pusher from the lid chute (in order to open
the lid it is necessary at rst to remove/lift the pusher out of
the chute).
5
Unlock and open the lid.
6
Remove the permanent guard.
7
Remove the disc.
8
Unlock the container.
9
Remove the container from the base.
10
Empty the container removing the products.
Operating instructions
Chipping and puree disc
During operation with chipping and puree disc it is
●
recommended to apply the blender drive speed 15 or
TURBO.
Insert the processed product into the feed chute, hold the
●
pusher (do not press), switch on the blender drive. When
the appliance is in operation press the pusher with a bit
of power.
When the container is lled up to MAX level, stop the
●
operation, empty it and collect the scrap accumulated on
the disc.
Slicing disc
During operation with slicing disc it is recommended to
●
apply the blender drive speed 15 or TURBO.
It is recommended to insert the products onto the feed
●
chute in vertical position so that they ll in complete
space of the chute.
Insert the processed product into the feed chute, hold the
●
pusher (do not press), switch on the blender drive. When
the appliance is in operation press the pusher with a bit
of power.
When the container is lled up to MAX level, stop the
●
operation, empty it and collect the scrap accumulated on
the disc.
OPERATION WITH ICE CRUSHER
The appliance characteristics
Zelmer hand blender is equipped with ice crusher which is
used for crushing ice and i.e. frozen fruits.
You can use the crusher only with the container
and lid of mini food processor!
Application of the accessories
Double-sided disc – is used for crushing, grinding ice and
frozen products. The disc is round, the blades are double-
sided. One side, which we recognize by the applied plastic
fteen- pointed star, g. 15a is used for rst level grinding
„I” (smaller particles of grinded product), the other side is
used for second level grinding „II” (bigger particles of grinded
product) and it is marked with seven-pointed star g 15b.
Spindle – is used for xing the disc.
Preparation of the ice-crusher
Before assembling and disassembling blender
motor drive On the ice crusher, make sure if
the supply cord plug is disconnected from the
mains supply outlet.
Wash the parts in contact with processed product before
rst usage.
Operate the blender so, that the closed/open markings
located on the appliance are well visible.
Operation with ice crusher (Fig. I)
1
Place the container of the mini food processor on rm,
at and dry surface.
2
Place the disc for ice on the spindle (double – sided disc),
so that the blades provided for operation are on the top.
3
Place the disc with the spindle inside the mini food
processor container so that the pivot protruding from the
container is inserted into the spindle orice.
4
Insert the ice crusher container on the fasteners of the
mini food processor. Then lock the crusher container, turning
it until you can feel it is blocked.
5
Place the processed products inside the container not
exceeding MAX level.
When you ll up the crusher container (14) with
appropriate amount of processed product (do not
exceed MAX level) center the spindle (16) (put in the
middle) to enable its proper coupling with the mini food
processor lid (10).
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 491 Symbio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 491 Symbio in the language / languages: English, Polish as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info