538892

Zelmer 13Z011 Manual

225
Zoom out
Zoom in
Previous page
1/228
Next page
225
16.10. Restoring factory settings
When the appliance is ready to use the message READY TO BREW appears on the display. To delete all settings made by
the user and to restore factory settings proceed according to the algorithm below.
ATTENTION! The language setting procedure is presented in section 16.2.
17. Warnings
The message a. MEASUREMENT ERROR TEMP. indicates that the temperature inside the coffee maker is too low (be-
low 2°C). If this message appears when the room temperature is above 2°C, it means that there is no sensor in the
coffee maker. Please contact your supplier for help.
The message b. TEMPERATURE TOO HIGH indicates that the temperature is too high during the operation of the coffee
maker. Cool the coffee maker and restart the appliance. If the message is still on the display after starting the appli-
ance, the sensor is damaged.
The message c. BREW UNIT BLOCKED indicates that the brewing head unit (14) is blocked and coffee cannot be
brewed. Open the service door (15), take out the brewing head unit (14) and check if it is in the “start position”. Next
reinstall the brewing head unit (14) and close the door (15). The whole procedure is described in section 4. Restart the
coffee maker. If the problem still exists even after unblocking the brewing head unit (14), turn to your supplier to solve
the problem.
The message d. RELEASE UNIT indicates that the brewing head unit (14) is slided out. Take out the dregs box (22),
close the service door (15) and restart the coffee machine. Press and hold for 5 seconds the (B)
button, the brew-
ing head unit (14) will slide out due to the reverse movement of the electric motor. Install the dregs box (22) properly
and brewing head unit (14) and close the door (15). Restart the coffee maker.
The message e. TOP SWITCH FAILURE indicates that the top switch above the brewing head unit (14) does not function
properly. Open the service door (15) to check if the brewing head unit (14) is blocked. After cleaning the unit (see sec-
tion 4) install the brewing head unit (14) and close the door (15). Restart the coffee maker. If you still hear the noise,
it means that the top switch is damaged and repair is necessary.
The message f. SET ROTARY KNOB indicates that the steam/hot water knob (13) is in the position during coffee
brewing. Set the knob (13) in the 0 position during coffee brewing.
The message g. DREGS BOX MISSING indicates that the dregs box (22) might not be properly installed during the cof-
fee brewing process. Check and install the dregs box (22) properly according to section 10.
The message h. FILL TANK WITH FRESH WATER indicates that there is not water in the tank (3). Immediately fi ll the
water tank (3) with fresh water according to section 6.
The message i. FILL TANK WITH SOLUTION indicates that there is no descaling solution in the tank (3). If this mes-
sage is displayed at the beginning of the descaling process, immediately fi ll the water tank (3) with the solution accord-
ing to section 16.7.
The message j. EMPTY DREGS BOX indicates that the coffee maker brewed 8 (9) cups of coffee. Empty and clean the
dregs box (22) according to section 10. It is also advantageous to clean the brewing head unit (14) according to sec-
tion 18.7.
The message k. DATA LOSS indicates the lack of initial settings in the EEPROM memory or the loss of this data. Further
operation of the coffee maker is only possible with default settings. This message disappears after 5 seconds.
The message l. WATER FLOW ERROR indicates that the brewing heat unit (14) fi lter is blocked or the water pipe is
blocked. Take out the brewing head unit (14) and check if the fi lter is blocked. If there are a lot of coffee remains, clean
the brewing head unit (14) (see section 18.7) and insert it back into place (see section 4). If there is no problem with
the brewing head unit (14) try to brew several cups of coffee or to prepare a cup of hot water. If you cannot remove the
brewing head unit (14) proceed according to section 19.7. If the problem still exists, the fl owmeter might be damaged.
The message m. DOOR OPEN indicates that the service door is open (15). Close the door.
The message n. NO ELECTROMAGNET SWITCH indicates that the sensor does not recognize the electromagnetic
switch. This message should disappear after 5 seconds. If the message appears several times it means that the elec-
tromagnetic switch might be damaged. The coffee maker must be repaired.
… 225 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 13Z011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 13Z011 in the language / languages: English, Polish as an attachment in your email.

The manual is 15,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info