517530
32
Zoom out
Zoom in
Previous page
1/36
Next page
32
User’s manual
EN
Problem Cause Remedies
“Safety Lift” appears on the display Front body sensor does not work
Makes sure the upper body is positioned correctly. If the
problem persists, contact your nearest authorised service
centre
“Sync error” appears on the display The robot’s receiver does not recognise the signal
Turn the robot off and then turn it back on again. If the problem
persists, contact your nearest authorised service centre
“Too high grass” or “Blade Error”
appears on the display
Cutting blade damaged Replace the blade with a new one (see “Blade Replacement”)
Cutting blade fouled (tape, cords, plastic
fragments, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Warning - Caution
Use protective gloves to prevent injury.
Unclog the blade
The robot was started too close to obstacles
(less than a distance of m) or in the presence of
obstacles (fallen branches, forgotten objects, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Remove the obstacles and restart the robot (see “Start-up and
manual stopping of the robot (in closed areas)”)
Electric motor failure
Have the motor replaced or repaired by your nearest
authorised service centre
Too high grass
Increase the cutting height (see “Adjustment of cutting height”)
Carry out a preliminary cutting of the area with a normal
lawnmower
The remote control does not work
Programming error
Correctly program the remote control (see “Programming
Mode”)
The LED of the remote control does not light up Remove the batteries and replace them
“Safety Lift” appears on the display
Sensor indicating the presence of the body is not
positioned correctly
Remove the hood, makes sure it is correctly inserted in the
front slot
“Watchdog error” appears on the
display
The internal “software safety” system is enabled
Turn the robot off and on. If the problem persists, contact your
nearest authorised service centre
“Tilt” appears on the display
The robot is located on a level that is higher than
the allowed limits
Mark off the area that is too steep
The robot is located on a level that is lower than
the allowed limits
Check that the charging station is positioned on a at surface.
Turn the robot off and on while in the charging station and try
again. If the problem persists, contact your nearest authorised
service centre
(C)
The led ( c
) does not
turn on
No power supply
Make sure the power supply unit is correctly connected to the
power outlet
Interrupted fuse
Have the fuse replaced by your nearest authorised service
centre
The LED
(C) of the
transmitter
is on
Interrupted perimeter wire
Stop the robot safely (see “Robot Safety Stop”). Disconnect
the power plug from the power supply unit. Join the perimeter
wire
PARTS REPLACEMENT
RECOMMENDATIONS FOR REPLACING PARTS
Important
Replace and repair any parts according to the manufacturer’s instructions, or contact the service centre if these operations
are not included in the manual.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info