517530
31
Zoom out
Zoom in
Previous page
1/36
Next page
31
User’s manual
EN
Problem Cause Remedies
The work area is not completely
mowed
Not enough work hours Reset the working time (see “Programming Mode”)
Cutting blade fouled
Stop the robot safety (see “Robot Safety Stop”)
Warning - Caution
Use protective gloves to prevent injury
Clean the cutting blade
Cutting blade worn out
Replace the blade with an original spare part (see “Blade
replacement”)
Work area too big compared to the actual capacity
of the robot
Adjust the work area (see “Technical speci cations”)
The batteries are about to run out
Replace the batteries with original spare parts (see “Battery
replacement”)
The batteries do not charge completely
Clean and remove any oxidisations from the contact points of
the batteries (see “Robot Cleaning”). Recharge the batteries
for at least 12 hours
Secondary area not completely
mowed
Incorrect programming
Correctly program the secondary area (see “Programming
Mode”)
On the display appears “No Signal”
The perimeter wire is not connected correctly
(broken cable, no electrical connection, etc.)
Check the functioning of the electrical power supply, the
correct connection of the power supply-transmitter unit and
that of the charging station (see “Installation of charging station
and power supply-transmitter unit”)
On the display appears “Out of
border”
Too much slope
Delimit the area with too much slope (see “Planning of plant
installation”). Install the kit for working on ground with slopes
greater than 35% (see “Technical Speci cations”)
Perimeter wire laid incorrectly
Check that the wire has been installed correctly (e.g. too deep,
next to metallic objects, distance between the wire marking the
two elements less than 70 cm, etc.) (see “Planning of Plant
Installation”)
Perimeter wire marking the boundary of the
inside areas ( owerbeds, bushes, etc.) laid in an
anticlockwise direction
Reposition the perimeter wire correctly (anti-clockwise
direction) (see “Installation of perimeter wire”)
Overheated power supply unit
Adopt the appropriate measures to reduce the temperature of
the power supply unit (ventilate or modify the installation area,
etc.) (see “Planning of plant installation”)
Incorrect wheel transmission Check and, if necessary,correctly fasten the wheels
“Blackout” appears on the display
Interruption of the power supply to the transmitter Restart the robot
Overheated power supply un
Adopt the appropriate measures to reduce the temperature of
the power supply unit (ventilate or modify the installation area,
etc.) (see “Planning of plant installation”)
Presence of other installations nearby Contact an authorised Service Centre
Perimeter wire oxidised caused by damage to the
protective sheathing
Contact your nearest authorised service centre to check the
impedance (Ohm) of the perimeter wire
“Wheel error” appears on the display
Ground is uneven or contains obstacles
that prevent movement
Make sure the lawn to mow is even and does not contain
holes, stones or other obstacles. Otherwise, ll in any holes
and remove any obstacles (see “Preparation and marking the
boundaries of the work areas (primary and secondary areas)”)
Failure of one or both motors that operate the
transmission of the wheels
Have the motor replaced or repaired by your nearest
authorised service centre
“Bump Error” appears The bumper sensors are blocked Remove the hood and check the functionality of the sensors
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info