649510
20
Zoom out
Zoom in
Previous page
1/24
Next page
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose
specially designed for this type of use.
Water drainage
The drain hose can be hooked over the edge of
a sink using the plastic hose guide supplied
with the machine. Make sure that the sink is
empty and the plug hole is not blocked.
Make sure the end
cannot come un-
hooked when the ma-
chine is emptying.
This could be done
by tying it to the tap
with a piece of string
or attaching it to the
wall.
If the machine is permanently plumbed in, hook
the end of the hose into a standpipe installed
for the purpose. The standpipe must have an
internal diameter of at least 40 mm (1 1/2”) in
order that there is an air gap between the drain
hose and the standpipe. Make sure, that it is
designed in such a way, that the end of the
drain hose cannot be covered with water.
650-800 mm
40 mm
Whether discharging into a sink or a standpipe,
check that the end of the drain hose is neither
too high or too low. The top of the curve in the
hose’s end should be no more than 800 mm
(31.5”), and no less than 650 mm (25.6”)
above floor level.
40mm (1 1/2”) diameter
standpipe
Min 30 cm (12”)
The drain hose can be extended up to total 3,5
m. For the extension piece use a hose with an
internal diameter at least as large as that of the
machine's own hose. Use a suitable hose con-
nector.
Electrical connection
Any electrical work required to install this appli-
ance should be carried out by a qualified elec-
trician or competent person.
Warning! THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated on
the appliance’s rating plate.
Warning! Information on the
electrical connection is given on the
rating plate on the inner edge of the
appliance door.
The appliance is supplied with a 13 amp plug
fitted.
In the event of having to change the fuse in the
plug supplied, a 13 amp ASTA approved
(BS1363/A) fuse must be used.
20
www.zanussi.com
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZWC1301 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZWC1301 in the language / languages: English as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info