743393
10
Zoom out
Zoom in
Previous page
1/18
Next page
PG 10
Test Installation
Follow these procedures to verify you have correctly
installed the CT32.
TO CHECK FAN (If you connected the G wire):
Touch the fan icon on the HOME screen to turn the fan ON.
Verify that air is blowing from the system.
Touch the fan icon again to return to AUTO.
TO CHECK HEAT
Set the mode to HEAT by pressing the MODE button until
HEAT is displayed.
Touch the temperature display to bring up the MANUAL screen.
Touch the + icon and raise the target temp to change target temperature to about 5
o
F above room temperature;
allow the system 2 minutes to respond.
Verify that heat is blowing from the system. Return the Target Temperature to a normal setting. Return mode to
OFF by pressing the mode button.
If you have a heat pump, leave in off for 4 minutes before checking COOL.
TO CHECK COOL (do not operate AC if the outside temp is below 65
o
F)
Set the mode to COOL by pressing the MODE button until COOL is displayed.
Touch the - icon and lower cool Target Temperature to change target temperature to about 5
o
F below room
temperature. Allow the system 5 minutes to respond.
Verify that cool air is blowing from the system. Return mode to OFF by pressing the mode button.
HVAC Setup on Screen
IMPORTANT: Make sure the CT32 is powered up and
the mode is set to OFF. HVAC selection switches must be
set rst [pg 8].
• With mode in OFF press MENU and touch HVAC SET UP.
• Use +/- arrows to select HVAC SET UP number on
screen. The LCD display will show your selection and
indicate the number of stages you have selected. During
setup, 2nd stage will blink when both heat and cool have
2nd stages.
• Touch HOME to permanently save this conguration.
If you have a Normal HVAC system...
1 stage HEAT, 1 stage COOL select 1
2 stage HEAT, 1 stage COOL select 2
1 stage HEAT, 2 stage COOL select 3
2 stage HEAT, 2 stage COOL select 4
IMPORTANT: You must touch HOME after you have made you conguration selection.
This will save this conguration into permanent memory of the CT32.
If you have a HEAT PUMP HVAC system...
HEAT PUMP with no AUX heat select A
2 stage HEAT PUMP with no AUX select b
HEAT PUMP with AUX heat select C
HEAT PUMP with 2 stage AUX heat select d
2 stage HEAT PUMP with AUX heat select E
2 stage HEAT PUMP with 2 stage AUX heat select F
HEAT
2
ND
ST
G
HVAC
SETUP
COOL
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Z-Wave CT32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Z-Wave CT32 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info