743385
53
Zoom out
Zoom in
Previous page
1/56
Next page
CT100 Thermostat
Z Wave®
4. C-Wire/Battery Status (8-bit)
If 0x01, the thermostat is powered by a C-wire. If 0x02, the
thermostat is powered by batteries.
5. Humidity Reporting Threshold (8-bit)
This value determines the reporting threshold when association
reporting is enabled. Unsupported values are ignored.
6. Auxiliary/Emergency (8-bit)
If set to 0, auxiliary / emergency heat is disabled. All other values
(1-255) enable auxiliary / emergency heat. This can only be
enabled when the thermostat is set to Heat Pump mode.
7. Thermostat Swing Temp
The thermostat swing temperature is in units of 0.5 degrees
Fahrenheit. A value of 0x01 is 0.5F and 0x02 is 1.0F. The supported
values may vary from thermostat to thermostat but typically the
allowed values are 0.5F (0x01) to 4.0F (0x08).
8. Thermostat Diff Temp
The thermostat diff erential temperature is in units of 0.5 degrees
Fahrenheit. A value of 0x04 is 2.0F and 0x06 is 3.0F. The diff erential
temperature must be an integer value. Non-integer values, such
as 1.5F (0x03), should not be used. The supported values may vary
from thermostat to thermostat but typically, the allowed values are
2.0F (0x04) to 6.0F (0x0C).
9. Thermostat Recovery Mode
The Thermostat Recovery Mode can be either fast (0x01) or
economy (0x02).
CT100 Thermostat
Z Wave®
10. Temp Reporting Filter (16-bit)
Set Command Defi nition
When setting parameter 10, the set command must contain 4
bytes whereas the report frame will only contain 2 bytes. This is
because the additional 2 bytes in the set command qualify the
values being set. In this way the temperature threshold values can
be set in either Fahrenheit or Celsius.
So a set command will look like this: 0A 04 aa bb cc dd, where:
aa = either 01 to indicate that bb is in Celsius, or 09 to indicate that
bb is in Fahrenheit
bb = the value of the lower bound (0 to 124)
cc = either 01 to indicate Celsius that dd is in, or 09 to indicate that
dd is in Fahrenheit
dd = the value of the upper bound (0 to 124)
76543210
Command Class = COMMAND_CLASS_CONFIGURATION
Command = CONFIGURATION_SET
Parameter = 0x0A
Default RESERVED Size = 0x04
Precision (0x00) Scale Bound Size (0x01)
Temperature Filter Lower Bound
Precision (0x00) Scale Bound Size (0x01)
Temperature Filter Upper Bound
Parameter (8-bit)
The parameter is set to 10 (0x0A) for the temperature
reporting fi lter.
Default (1-bit)
If the default bit is set, the upper bound is zero (0) and the
lower bound is 124. This disables the fi lter.
Size (3-bit)
The Size fi eld must be set to 4 (100b).
Precision (3-bits)
The precision fi eld describes the precision of the temperature
lter value. The fi lter must be zero (0x00).
53
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Z-Wave CT100 PLUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Z-Wave CT100 PLUS in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info