669702
19
Zoom out
Zoom in
Previous page
1/40
Next page
18
After sliding the icon,
the remote control interface will display EXIT and [ ]. Tap the [ ]
the icon will become [ ]. Then the journey function will be paused. When tapped again, the
[ ] will become [ ], the H920 PLUS will continue the Journey function. Exit the function
by tapping EXIT icon or switching flight mode.
NOTICE:
When the Journey function is activated, the Journey distance may be set by the
pilot.
NOTICE:
The gimbal camera cannot be controlled when journey function is activated and
will remain the previous angle set before. Depending on the camera tilt, the H920 PLUSwill
fly up and out to take the perfect self-shot, or “selfie”.
NOTICE: The journey route is the reverse direction to which the gimbal camera is facing.
1/3
2
ORBIT ME: When Orbit Me is enabled, H920 Plus flies a circular path around the pilot.
Press ORBIT to enter the ORBIT ME function.
START:
Press START, and slide the icon, push the aileron stick to the right or left. The H920
PLUS will fly around the pilot/ST16 with the distance between the start point and the pilot as
the radius.
BACK: Tap BACK to return to the previous interface.
NOTICE: You can increase/decrease radius by apply forward/back on right stick.
You also can trim the gimbal pan position by adjusting pan control knob on ST16 under
Follow or Follow controllable mode in Pan direction..
NOTICE: The tilt direction of gimbal camera can be adjusted by the camera tilt control knob.
NOTICE:
If the aircraft ies too close to the pilot, it will automatically enlarge the distance and
then begin to orbit.
NOTICE: Adjust the Throttle Control joystick to change the height of the aircraft, adjust the
Aileron Control joystick to change the orbit direction of the aircraft.
[ ]: When the pilot tap the [ ] the icon will become [ ]and the ORBIT ME function will
be paused. When tapped again, the [ ] will become [ ], the copter will continue the ORBIT
ME function. Exit the function by tapping EXIT icon or switching flight mode.
18
Nachdem Sie über das Symbol gewischt haben, zeigt der Bildschirm der Fernbedienung „EXIT“ und [ ] an.
Wenn Sie auf [ ] tippen, wechselt das Symbol zu [ ]. Die Journey-Funktion wird dann pausiert. Wenn Sie er-
neut darauf tippen, wechselt [ ] zu [ ], und der H920 PLUS führt die Journey-Funktion weiter aus. Sie können
die Funktion beenden, indem Sie auf das EXIT-Symbol tippen oder den Flugmodus wechseln.
HINWEIS: Wenn die Journey-Funktion aktiviert ist, kann der Pilot die „Journey“-Entfernung festlegen.
HINWEIS: Die Gimbal-Kamera kann nicht gesteuert werden, während die Journey-Funktion aktiviert ist, und
bleibt in dem zuvor eingestellten Winkel stehen. Der H920 PLUS iegt je nach Kameraneigung in die Höhe, um
die perfekte Selbstaufnahme bzw. das perfekte „Sele“ aufzunehmen.
HINWEIS: Die Flugroute („Journey“) verläuft entgegen der Richtung, in welche die Gimbal-Kamera zeigt.
ORBIT ME (Mich umkreisen): Wenn „Orbit Me“ aktiviert ist, umiegt der H920 Plus den Piloten in
einer kreisrunden Flugbahn.
Drücken Sie auf „ORBIT“, um die Funktion ORBIT ME aufzurufen.
START (Starten): Drücken Sie auf „START“, wischen Sie über das Symbol und drücken Sie den Querruder-Hebel
nach rechts oder links. Der H920 PLUS umkreist dann den Piloten/die ST16 und nimmt dabei als Radius die
Entfernung zwischen dem Startpunkt und dem Piloten.
BACK (Zurück): Tippen Sie auf „BACK“, um zur vorherigen Oberäche zurückzukehren.
[
]: Wenn der Pilot auf [ ] tippt, wechselt das Symbol zu [ ], und die ORBIT-ME-Funktion wird pausiert. Wenn
er erneut darauf tippt, wechselt [ ] zu [ ], und der Copter führt die ORBIT ME-Funktion weiter aus. Sie kön-
nen die Funktion beenden, indem Sie auf das EXIT-Symbol tippen oder den Flugmodus wechseln.
Sie können außerdem die Gimbal-Schwenkposition anpassen, indem Sie den Schwenksteuerknopf an der ST16
unter „Follow“ oder „Follow controllable mode“ in „Pan-Richtung einstellen.
HINWEIS: Die Neigungsrichtung der Gimbal-Kamera kann mit dem Neigungssteuerungsknopf der Kamera
angepasst werden.
HINWEIS: Wenn das Fluggerät zu nah am Piloten iegt, vergrößert es automatisch den Abstand und beginnt
dann, ihn zu umkreisen.
HINWEIS: Bewegen Sie den Gashebel, um die Höhe des Fluggeräts zu verändern; bewegen Sie den Querru-
der-Hebel, um die Richtung der Umlaufbahn des Fluggeräts zu ändern.
18
After sliding the icon, the remote control interface will display EXIT and [ ]. Tap the [ ]
the icon will become [ ]. Then the journey function will be paused. When tapped again, the
[ ] will become [ ], the H920 PLUS will continue the Journey function. Exit the function
by tapping EXIT icon or switching flight mode.
NOTICE:
When the Journey function is activated, the Journey distance may be set by the
pilot.
NOTICE:
The gimbal camera cannot be controlled when journey function is activated and
will remain the previous angle set before. Depending on the camera tilt, the H920 PLUSwill
fly up and out to take the perfect self-shot, or “selfie”.
NOTICE: The journey route is the reverse direction to which the gimbal camera is facing.
1/3
2
ORBIT ME: When Orbit Me is enabled, H920 Plus flies a circular path around the pilot.
Press ORBIT to enter the ORBIT ME function.
START:
Press START, and slide the icon, push the aileron stick to the right or left. The H920
PLUS will fly around the pilot/ST16 with the distance between the start point and the pilot as
the radius.
BACK: Tap BACK to return to the previous interface.
NOTICE: You can increase/decrease radius by apply forward/back on right stick.
You also can trim the gimbal pan position by adjusting pan control knob on ST16 under
Follow or Follow controllable mode in Pan direction..
NOTICE: The tilt direction of gimbal camera can be adjusted by the camera tilt control knob.
NOTICE:
If the aircraft ies too close to the pilot, it will automatically enlarge the distance and
then begin to orbit.
NOTICE: Adjust the Throttle Control joystick to change the height of the aircraft, adjust the
Aileron Control joystick to change the orbit direction of the aircraft.
[ ]: When the pilot tap the [ ] the icon will become [ ]and the ORBIT ME function will
be paused. When tapped again, the [ ] will become [ ], the copter will continue the ORBIT
ME function. Exit the function by tapping EXIT icon or switching flight mode.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Plus in the language / languages: German as an attachment in your email.

The manual is 3,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yuneec Tornado H920 Plus

Yuneec Tornado H920 Plus Quick start guide - English - 2 pages

Yuneec Tornado H920 Plus User Manual - English - 40 pages

Yuneec Tornado H920 Plus Quick start guide - German - 2 pages

Yuneec Tornado H920 Plus User Manual - French - 40 pages

Yuneec Tornado H920 Plus Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info