669702
18
Zoom out
Zoom in
Previous page
1/40
Next page
17
Model: H920 Plus welcome,Pilot12:27 AM12
VOLTS
GPS
SAT
POS
ALT
G-SPD
DIS
N/A
N/A
N/AE
N/AN
N/AV
N/Am
N/A KPH
N/Am
System SettingsPad
Channel Settings
Model Select
TASK
CAMERA
GPS
CALIBRATION
FOLLOW
WATCH
ANGLE
G
Disabled
OBS
BACK RESETLISTSAVE
START
SLIDE TO START
CANCEL
Make sure the H920 Plus is clear of all
obstacles before starting mission.
CCC
PONINT 1PONINT 1
PONINT 2
PONINT 3
INSTRUCTION
RESET: Delete all waypoints
+/-: Add/Delete a waypoint
LIST: Load existing waypoint
SAVE: Save waypoint
START: Start waypoint mission
T
ap the CCC to enter the Curve Cable Cam function.
BA
CK: Tap BACK to return to the previous interface.
RESE
T: Tap RESET to delete all the points created during the flight.
:
Tap '-' to delete the last point created during the flight.
:
Tap '+' to create a new point recording the current flying position.
LIS
T: Tap LIST and all previous missions/routes saved will be shown on a
list
. Delete any saved mission/route by sliding the chosen one to the
lef
t.
SA
VE: Tap SAVE and the current mission/route will be saved.
ST
ART: Tap START, and slide the icon. H920 PLUS will y back to
waypoint 1 automatically
.
BACK RESET LIST SAVE
START
[ ]: When the pilot tap the [ ] the icon will become [ ]and the CCC
function will be paused. When tapped again, the [ ] will become [ ], the
copter will continue the CCC function. Exit the function by tapping EXIT
icon or switching flight mode.
JOUR: The Journey function enables the H920 PLUS to capture perfect aerial self-shots, or a fly
to/from scenic shot with perfect motion. When enabled, the H920 will fly away, up, and return.
Tap JOUR to enter the journey function.
START: Select JOUR and set the distance, then slide the slider. H920 PLUS will y up and out to
take a photo or video.
BACK:
Tap BACK to return to the previous interface.
If the pilot set 7 waypoints as shown, when the copter arrives at the Waypoint 1, slowly ra
ise
the throttle stick, the copter will fly along the waypoints from 1 to 7 in order. If
the pilot slowly
lower the throttle stick, the copter will fly along the waypoints from 7 to 1 in order.
6
7
1
2
3
4
5
17 18
Tap the CCC to enter the Curve Cable Cam function.
BACK: Tap BACK to return to the previous interface.
RESET: Tap RESET to delete all the points created during the ight.
: Tap ‚-‘ to delete the last point created during the ight.
: Tap ‚+‘ to create a new point recording the current ying position.
LIST: Tap LIST and all previous missions/routes saved will be shown on a list. Delete any saved mission/route by
sliding the chosen one to the left.
SAVE: Tap SAVE and the current mission/route will be saved.
START: Tap START, and slide the icon. H920 PLUS will y back to waypoint 1 automatically.
[ ]: When the pilot tap the [ ], the icon will become [ ] and the CCC function will be paused. When tapped
again, the
[ ] will become [ ], the copter will continue the CCC function. Exit the function by tapping EXIT icon or swit-
ching ight mode.
If the pilot set 7 waypoints as shown, when the copter arrives at the Waypoint 1, slowly raise the throttle stick, the
copter will y along the waypoints from 1 to 7 in order. If the pilot slowly lower the throttle stick, the copter will y
along the waypoints from 7 to 1 in order.
JOUR: The Journey function enables the H920 PLUS to capture perfect aerial self-shots, or a y to/
from scenic shot with perfect motion. When enabled, the H920 will y away, up, and return.
Tap JOUR to enter the journey function.
Start: Select JOUR and set the distance, then slide the slider. H920 PLUS will y up and out to take a photo or video.
BACK: Tap BACK to return to the previous interface.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Plus in the language / languages: English as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yuneec Tornado H920 Plus

Yuneec Tornado H920 Plus Quick start guide - English - 2 pages

Yuneec Tornado H920 Plus Quick start guide - German - 2 pages

Yuneec Tornado H920 Plus User Manual - German - 40 pages

Yuneec Tornado H920 Plus User Manual - French - 40 pages

Yuneec Tornado H920 Plus Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info