733774
22
Zoom out
Zoom in
Previous page
1/33
Next page
42 43
Setting the mowing height
The mower’s mowing height can be set between 20 and 60 mm with 5 cutting heights. If
the grass is higher than 60 mm, it will be necessary to mow the grass using a standard
lawnmower. Otherwise, the grass will cause too great a load for the mower’s blades and thus
lead to unsatisfactory mowing. Do not adjust the cutting height during mowing.
1. Press the main isolation switch to turn off the mower.
2. Open the top cover.
3. Rotate the mowing height selector to adjust the mowing height.
• It is recommended to begin with mowing by setting the mowing height to 60 mm (by
setting the selector to MIN) and then gradually lowering the mowing height until you get
the desired grass height.
4. Close the top cover after the adjustment.
Note: The mower can cut on wet grass. However this will lead to clumps of grass
forming under the mower which means more frequent cleaning of the mower is
necessary.
Starting and stopping the mower
Starting the mower
1. Make sure the mower is sufciently charged.
2. Press the main isolation switch to turn on the mower.
3. Press the STOP button to open the control panel cover.
4. If a PIN is set, enter the PIN with the number keys on the display .
5. Press the START button in the control menu.
6. Close the control panel cover. The mower will start mowing.
Note: The mower can be programmed to automatically start mowing at specific times
and on specific days in a week. See the section: Programming the mower.
Stopping the mower
• Press the STOP button(2) to immediately stop the mower.
Note: Once the STOP button is activated, the control panel cover will open and the
mower will wait for further commands. The mower will not start to work until the control
panel cover is closed.
Messages on the display during operation
While mowing, the display will show the operating status of the mower.
Information includes the current date and time, battery level, boundary cable signal
(S1 or S2) and operation status message (see below).
Message Description
Running
The mower is working. When the blade disc starts to rotate, the
blade disc icon (
) will show and ash on the display.
Home
The mower is in the process of returning to the charging sta-
tion.
Low voltage
The battery power is low and the mower will return to the
charging station.
Charging The mower is being charged.
No signal There is no boundary cable signal.
Outside The mower has moved outside the mowing zone.
Trapped
The obstacle sensor gives continuous alert for more than 10
seconds. The mower has stopped for safety reasons.
Pit
The obstacle sensor has triggered more than 10 times in one
minute. The mower has stopped for safety reasons.
Slope
The mower has encountered a steep slope which it cannot
overcome.
Lifted
The mower has either been lifted up or risen up over an obsta-
cle.
Error Incorrect PIN passcode is entered.
OPERATION
OPERATION
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce SA800PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce SA800PRO in the language / languages: English as an attachment in your email.

The manual is 6,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info