Manual Yamaha XV920 Virago (page 331 of 363) (English)

689861

331

Zoom out

Zoom in

1/363

8B-10

Chapter 8 Part B Electrical system (XV700-1100 models)

13.6 Remove the speedometer securing

nut and lift the speedometer out

14.1a Remove the warning light cover

screws and lift off the cover ...

14.1b ... and pull the bulb from

the socket

5 If you're working on a 1981 through 1983 XV750, an XV920J, or

an XV920 K or MK, disassemble the cluster as necessary for access to

speedometer,

6 If you're working on an XV920 RH, XV920 RJ or TR1. remove the

nut, washer and grommet from the back of the speedometer housing

and remove the speedometer (see illustration).

7 If you're working on a 1984 or later model, lift the speedometer

away from the bracket and turn it over. Remove the self-tapping screw

and detach the speedometer from the housing (see illustration 13.5 in

Part A of this Chapter). Follow the speedometer wiring harness to its

connector (inside a rubber cover below the speedometer) and

disconnect it.

Installation

8 Installation is the reverse of the removal procedure. Be sure the

speedometer cable and wiring harness are routed so it doesn't cause

the steering to bind or interfere with other components. The squared-

off ends of the cable must fit into their spindles in the speedometer and

drive gear.

14 Instrument and warning light bulbs - replacement

Refer to illustrations 14.1a, 14.1b and 14.3

1 To replace a warning light bulb on an XV920 RH, XV920 RJ or

TR1, remove the warning light cover screws (see illustration). Pull the

bulb outof its socket (see illustration), push in a new one and install

the cover.

2 To replace an instrument light bulb on an XV920 RH, XV920 RJ or

TR1, remove the speedometer or tachometer (see Section 13). Pull the

bulb socket from the back of the instrument, pull the bulb out of the

socket and push in a new one. Reinstall the instrument.

3 To replace bulbs on an XV920J, remove the instrument cluster

from its mounting bracket (see Section 13). Pull the bulb socket from

the bottom of the instrument cluster (see illustration), pull the bulb out

of the socket and push in a new one. Reinstall the instrument cluster.

4 To replace bulbs on an XV750, XV920K or XV920 MK, remove the

cluster partway and remove the lower cover (see Section 13). Pull the

bulb socket from the bottom of the instrument, pull the bulb out of the

socket and push in a,new one. Reinstall the instrument cluster.

15 Ignition main (key) switch - check and replacement

Check

Refer to illustration 15.2

1 Follow the wiring harness from the ignition switch (on the upper

triple clamp) to the connector and disconnect it.

2 Using an ohmmeter, check the continuity of the terminal pairs

indicated in the accompanying table (see illustration). Continuity

should exist between the terminals connected by a solid line when the

switch is in the indicated position. Note: Connect the ohmmeter to the

switch side of the connector, not the wiring harness side.

3 If the switch fails any of the tests, replace it.

14.3 On chain drive models, remove the instrument and pull the

bulb socket from its underside, then pull the bulb from the socket

15.2 Ignition (main key) switch continuity diagram

1 XV920J, 1984-on 1000 and XV1100 only

2 XV920J only

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV920 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yamaha XV920 Virago Manual

Product: