557718

Yamaha MX-D1 Manual

7
Zoom out
Zoom in
Previous page
1/72
Next page
5
English
Speaker cables typically consist of two insulated
conductors. To ensure that the speakers are connected with
the correct polarity (+/-), the insulation on one of the
conductors is a different color or is marked with a line.
1. Strip about 15 mm (5/8”) of insulation from
the ends of the speaker cables.
2. Twist the bare wires tightly to prevent a
short circuit.
3. Unscrew the SPEAKER terminals.
4. Insert the twisted bare wires into the holes
on the SPEAKER terminals.
5. Screw the SPEAKER terminals tight.
When using banana plugs, tighten the terminal knob
and insert the plug into the end of the terminal.
(With the exception of U.K., Europe and Korea models)
Connecting to the BALANCE jacks
Connect your component with the balanced XLR
output jacks.
The pin assignments for these jacks are shown below.
Refer to the owner’s manual of your component and
verify that its output jacks are compatible with the pin
assignments for these jacks.
When connecting, match the pins and insert the
connector of the XLR cable until you hear a “click.”
When disconnecting, pull out the XLR cable while
holding down the lever of the BALANCE jack.
When using this balanced connection, set the UNBAL/
BAL switch to “BAL.”
Connecting to the UNBALANCE jacks
Connect your component with the unbalanced RCA
output jacks.
When using this unbalanced connection, set the
UNBAL/BAL switch to “UNBAL.”
Do not connect your components to both of the
BALANCE jacks and UNBALANCE jacks.
Plug the power cable into the AC IN connector when all
connections are complete, and then plug in the power
cable to the AC outlet.
Caution
When inserting the stripped ends of the speaker
wires as shown above, make sure at least 1/16
inch (1.6 mm) of insulation is inside the wire
holders (i.e no exposed wire is visible) and no
loose conductor wire strands are protruding
after connection. If wires touch each other or
they touch the metal parts of this unit, this unit
and/or speakers could be damaged. To prevent
speaker wire from coming loose, make sure wire
holder are firmly screwed in.
Connecting Your Speakers
15mm
1
2
4
33
5
Red: + (positive)
White: - (negative)
Banana plug
Connecting Your Source
Components
2: hot
1: ground
3: cold
Caution
Connecting the Power
Cable
01-MX-D1_GB_E.fm Page 5 Wednesday, October 22, 2003 2:05 PM
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MX-D1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MX-D1 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info